曲线角

It seemed that segments must be short enough so that any curve that developed would be well defined, i.e., there should be some maximum angle between adjacent segments, perhaps 0.1 radians.

它 看来，部分必须太长，从而使任何曲线，发达国家将是很好的界定，也就是说，应该有一些最大角相邻部分，也许0.1弧度。

1The axial evolution law on the structure and the aerodynamic characteristics of the asymmetric flows around slender bodies of revolution at incidences is summarized:whether the flow asymmetry is powerless or powerful,the flow always appears in the structure that lee-side vortices rise,and shed vortices form,and new lee-side vortices come into being alternately on opposite sides of a slender body of revolution axially from nose apex downstream to afterbody,and always induces the sectional side force of waving quasi-sinusoidally downstream axially.

1总结出细长旋成体有攻角非对称绕流流场结构和气动力特性的轴向演化规律：无论非对称性强弱，沿轴向从头部尖顶往后体，非对称绕流总是呈现为左、右两侧背涡交替从物面向上飘起、形成脱落涡、再衍生出新生背涡的流场结构，并诱导出沿轴向呈类似正弦曲线形式振荡分布的截面侧向力。

Generally,C p curve can be regarded as a nonlinear function of pitch angle and tip speed.

通常情况下，功率曲线与桨距角和叶尖速比有关，可以看成是它们的非线性函数，一般由气动性能计算得到。

Innovative automobile electronic ignition control system is based on the characteristic curve MAP of ignition advance angle to control data,and the insertion value algorithm and changing index exponent curve surface fitting algorithm are chosen dynamically.

新型汽车电子点火控制系统是以点火提前角的特性曲线MAP图为基础控制数据，动态选用插值算法和变阶曲面拟合算法。

By way of research, the profile curve of offset translating follower plate cam for realizing zero degreed pressure angle was explored.

压力角越小传力性能越好，经过研究，探索出了在推程中实现零度压力角的偏置直动从动件盘形凸轮轮廓曲线。

The fatigue strength of duplex stainless steel welded jointing with longitudinal fillet welded gusset and with longitudinal flat side gusset welded on plate were evaluated by hot spot stress,and the hot spot stress S-N curves were obtained and compared with the nominal stress S-N curves.

针对双相不锈钢焊接结构的疲劳性能问题，通过试验对双相不锈钢纵向角接板焊接接头和侧面角接板焊接接头疲劳强度用热点应力进行了评定，做出了热点应力S N曲线并与名义应力疲劳评定进行了比较。

For cutting the composite lock gear with unequal tooth thickness, a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile. The cutter tooth arrangement, the choice of teeth number of the cutter and the basic method of cutter design are discussed; and a new method of choosing deflection factor by using limited area is presented.

研究加工不等齿厚的非标准参数渐开线齿形，与非渐开线齿形复合的锁闭齿轮插齿刀刀齿的排列、刀具齿数的选择以及刀具设计的基本方法，介绍用限制区域选择插齿刀变位系数的新方法，并给出刀具齿顶后角与侧螺旋角的关系曲线，为插齿刀参数的选择提供依据。

Themapping function sequences including circular cutouts and elliptical cutouts aregiven in this chapter.

然后为方便地满足圆柱壳大开孔的边界条件，通过复变函数方法中的用来求解多边形映射问题的Schwarz-Christoffel积分表达式，将圆柱壳展开面上的非圆非椭的开孔边界曲线保角映射成为单位圆，给出了在不同开孔率情况下的关于圆孔和椭圆孔的保角映射函数的具体形式。

And analysis the output curve after improving, and in the same time, the difference in the corresponding angular speed, angular acceleration, angular displacement curve of the bilateral symmetry components will obviously decrease.

并分析改进后的输出曲线，在同样的时间段内左右对称传动构件相应的角位移、角速度以及角加速度之间的差异明显减小。

On the basis of the modeling and analyzing of the transmission system of the PQS-3-D elevator for car in the preamble, this article analysis the reason of the small difference of the angular speed, angular acceleration, angular displacement curve between the bilateral symmetry components. Actually, it is the result of that the torsional rigidity of the bilateral drive shafts are different, therefore has made the revision suggestion to the drive shaft parameter.

在对PQS-3-D型汽车专用升降机传动系统建模分析的基础上，分析左右对称传动构件的角速度、角加速度、角位移曲线在系统起动时间内有较小差异的主要原因，发现是由于左右传动轴的扭转刚度系数不同造成的，故对传动轴的参数做了修改建议。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。