曲率

Said second leading edge member has a circular configuration with a radius significantly smaller than the radius of curvature of the arcuate configuration of said other airfoil means.

说，第二领先会员有一个圆形的配置与半径显着小于曲率半径弓状的配置说，其他翼型的手段。

Focal error signal of pickup head is achieved according to the Astigmatical principle, and that the optical non-contact probe system with the measurement ranges of 2um and the measurement uncertainty of 1.1nm is obtained. This probe system is immune to the variation of reflective ratios and curvature on the surfaces of samples via improvement of the signal process method.

其中根据光学象散原理得到激光读取头的聚焦误差信号，从而获得测量范围为2μm，测量不确定度可达1.1nm的光学非接触探头系统，通过改进信号处理方式，此探头系统可不受材料表面反射率变化的影响，并允许样品表面存在一定的曲率变化。

First, the cross section of a boxlike girder is discretized into stiffened elements and corner elements, then the FEM program is compiled to calculate the curve between stress and strain of every stiffened element.

加筋板单元是船舶与海洋工程等箱型梁结构的主要组成构件，首先将箱型梁剖面离散成若干加筋板单元和角单元，利用非线性有限元方法逐一计算加筋板单元的应力—应变关系曲线，然后再用逐步破坏分析法得到整个结构的弯矩—曲率曲线，从而求得其极限弯矩。

The interior flow of pump is the quite complicated turbulent flow. It is affected not only by the circumrotation and the surface curvature of impeller, but also by the sandy materials, even has the backflow and disengaged flow. They are one of the rather complicated numerical calculations in the fluid engineering field.

离心泵的内部流动是很复杂的湍流流动，同时由于受旋转、叶片表面曲率和泥沙颗粒的影响，还拌有脱流、回流等流动现象，是流体工程中较难的试验研究和数值计算问题之一。

This paper analyses the coupling wastage in columniform wave guide gas laser,and gives the function between the coupling wastage of laser guide modulo EH11 and the position and radius of reflector.

分析了圆柱形波导气体激光器中的耦合损耗，给出了最低阶波导模EH11的耦合损耗与反射镜位置、曲率半径的函数关系。研究表明：反射镜的位置和半径存在着最佳值，在取得最佳值时，可得到最低的耦合损耗

The whole machine performance curve of air blower made in accordance with controllable eddy ternary current rotator technology is complanate,its surging outflow is little, and it can ensure the design calculation astringentyunder the condition of wider blade or small curvature radius.

按照可控涡三元流转子技术制造的鼓风机的整机特性曲线平坦，喘振流量小，可确保宽叶片或小曲率半径条件下设计计算收敛。

The practice of predicting natural fracture zones in deep formation in An Peng oilfield indicates that the extremum main curvity method has definite reliability in predicting pull apart fractures of homogeneous terranes.

安棚油田深层系预测天然裂缝发育带的实践表明，极值主曲率法在结构均一岩层构造拉张裂缝的预测中具有一定的可信度。

For guaranting the centre of oscillating axle in oscilla tor head being coincident with the centre of hone 's arc surface and centre of raceway curvity, JFX series optical diopters are adopted for adjustment.

在球轴承套圈沟道超精时，为保证振荡头摆轴中心、油石圆弧面中心和沟道曲率中心三者重合，采用JFX系列光学瞄准器具有很多优点，文中介绍了该仪器的光学原理、使用方法和注意事项等。

The key for the optical design is confirming the F number of lens,and making the system aberration least by transforming the curvature of lens and the degree of lens tilt in the case of no ghost image damager.

设计的关键在于确定例行的透镜F数。并通过控制透镜的曲率半径和倾斜角度，在保证无鬼点破坏的情况下使得系统像差较小。

Both of them are designed according to the principle of Benkelman beam deflectometer.

这两个方案的路面曲率半径仪都是以路面弯沉仪为基础的。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐