曲柄行程

The method of setting up an affine coordinates system to solve the problems for the spatial crank and rocker mechanism is proposed.

分析并回顾了在给定摇杆两个极限位置及行程速度变化系数的情况下，最小传动角为最大的平面曲柄摇杆机构和空间曲柄摇杆机构的设计问题。

The article bases on the traditional graphical method,and applies design principle in the references[1],derives the optimizing design methods which under the condition of meeting the fixed slider stroke and the coefficient of variety of stroke velocity,makes the minimum transmission angle of the eccentric crank slider mechanism to maximum(that is the best transmission angle).

曲柄滑块机构在工程上应用十分广泛，传动角的大小是衡量机构传力性能好坏的一个重要指标。通常求解最佳传动角的方法是建立数学模型，在计算机上进行数值求解，本文在传统图解法的基础上，运用文献[1]中的设计原理，推导出在满足给定的滑块行程S和行程速度变化系数K的条件下，使传动

This paper made an improvement and development on the traditional graphic solution method for designing planar crank-rocker mechanism in accordance with travel velocity-ratio coefficient K .

对传统的按行程速比系数K设计平面曲柄摇杆机构的图解法做了改进，使该法在解决带有辅助条件的设计问题时更为简捷。

By making use of contraction mapping principle and similar matrices and graphical method ,this paper discusses some methods of asking its limit in accordance with recurrent sequence of number.3. The criteria whether Ⅰ,Ⅱ,Ⅲ types of crank-rocker mechanisms exist are given and the graphical method of synthesizing crank-rocker mechanisms with quick return characteristics are proposed.

针对目前具有急回特性的曲柄摇杆机构综合中存在的不足，对这类机构的图解法综合进行了深入的探讨，得到了行程速比系数和摇杆摆角取不同值时，Ⅰ型、Ⅱ型、Ⅲ型曲柄摇杆机构是否有解的判据，并给出用图解法综合具有急回特性的曲柄摇杆机构的方法。

Cutting machine used crank slider, and switches used itinerary electromagnet with the realization of the fixed-length wire control.

切断机采用了曲柄滑块机构，采用行程开关和电磁铁配合的方式实现线材的定长控制。

Crank endplay device should be used in long work piece changing in to thin stretching process,the device will make gliding block to be realized un iform motion in working process.

在长工件变薄拉伸加工中应选用曲柄—摇杆机构，此机构能使滑块在工作行程中实现平稳的匀速运动，并可获得较高的工件表面质量。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。