显微镜

The expression of cytochrome C, FLIP and Ca2 concentration were also measured.

用共聚焦显微镜观察3株细胞中Ca2 的浓度。

The gauge block surface under test is imaged by the interference microscope. The interference image is acquired and transmitted to the computer by the digital CCD video camera. Digital image processing technology is used to extract the edge contour line and midline of the interference dark fringe.

待测量块表面经干涉显微镜所成的干涉图像由数字CCD 摄像头采集并传输到计算机中，利用数字图像处理技术，对干涉条纹的边缘和中线进行提取，计算出量块表面粗糙度评定参数。

The datum line and mainly three profile height parameters of surface roughness are briefly introduced and the operation principle and system structure of AFM.

简要介绍了评定表面粗糙度参数的基准线及其主要的两个轮廓高度评定参数，详细阐述了重庆大学研制成功的一种高精度原子力显微镜——AFM。

The morphology, occurrence and components of dawsonite were described, and the paragenetic sequence of sandstone and origin of CO2 forming dawsonite were investigated by polarization microscope, scanning electron microscope, Xray diffraction and MAT251 stable isotope mass spectrometer.

利用偏光显微镜、扫描电镜、X射线衍射分析仪和MAT251稳定同位素质谱仪，详细描述了片钠铝石的形貌、产状和成分，确定了含片钠铝石砂岩的成岩共生序列和形成片钠铝石的CO2的成因。

Finally, the proposed nanodevices were illuminated by 0.16 mW / cm2 daylight lamp.

在扫描式电子显微镜的观察下，证明其结构成功地生长於矽基板上。

A systematic analysis of the various combinations of the hexagonal, boat, and pentagonal star in the crystalline approximants of decagonal quasicrystal has been made. This was compared with the structural subunits in some approximants observed by high-resolution electron microscopy.

系统地分析了二维十重准晶的近似晶体相中六角、船形和五角星等结构块的不同排列组合，并与我们已用高分辨电子显微镜观察到的一些近似相中的结构单元进行了比较。

The several shapes of diamond grains have been observed in SEM: truncated cube, octahedron, truncated cubo-octahedron, twinned cubo-octahedron, twinned regular decahedron and twinned regular icosahedron. Most of diamond grains are octahedron.

用扫描电子显微镜观察到多种外形的金刚石颗粒：截顶立方体、未截顶正八面体、截顶立方八面体、孪晶立方八面体、正十面体和正二十面体的金刚石颗粒。

A decay constantβof 0.98 per methylene group is measured. Electron transport propeties for n-alkanedithiol monolayers on Au(111) is investigated using conducting atomic force microscopy.

使用导电原子力显微镜方法研究了在Au(111)表面上的硫醇分子自组装膜的电子输运特性。

The prior cycles with higher axial stress and larger strain range greatly restrains ratchetting strain of subsequent cycling with lower ones. Creep behavior plays an important role in the ratchetting strain and its influence on ratchetting behavior can not be neglected. Fracture morphology characteristics of two kinds of materials were investigated by scanning electron microscope. It shows that failure of material A is induced by cavitation and that of material B is induced by decohesion. For material A, with the decreasing strain amplitude the fracture surface shows more larger diameter globular particles under uniaxial loading and can be seen more obvious and deep crack under multiaxial loading. However for material B, with the decreasing strain amplitude fracture surface shows larger and larger scalelike shape and becomes more smooth under uniaxial loading, but fracture surface under multiaxial loading looks like more smooth than that of uniaxial loading, and shows gradually wave-like morphology.

通过扫描电子显微镜研究表明：材料A为空穴引起的失效，材料B为剥离导致疲劳破坏；随着载荷幅值的减小，材料A在单轴载荷下，断口表面浮出更多更大直径的球状颗粒，而多轴载荷下，可以看到很深的裂纹；随着载荷幅值的减小，材料B在单轴载荷下，断口表面鱼鳞片越来越大，表面越来越平整，而多轴载荷与单轴载荷相比，断口表面看上去更加平整，并且随着载荷幅值的减小，断口逐渐呈现波浪形貌；通过微观的傅立叶变换红外光谱分析，结果表明随着应变幅值的增加，无论载荷是单轴还是多轴状态下，橡胶材料吸光度比值随着幅值的增加而增加，这说明体系中的结晶含量也随之增加。

By direct microscopic observations of thin section of Inada granite in the heating process, decrepitation temperature of fluid inclusions in quartz and feldspar was determined to be in a range from 170℃ to 550℃, and thermal microcracking due to the decrepitation of the fluid inclusions was ascertained.

通过常温及高温显微镜观察，查明了稻田花岗岩中流体包裹体的初始分布状态，并发现在高温条件下，由于流体包裹体的爆裂而导致花岗岩中微小裂纹的形成。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。