易变形的

Real contact between two surfaces occurs only at the asperities, which resulted in the fact that the asperities in real contact carry high load and are prone to elasto-plastic deformation.

摩擦副接触表面的接触只发生在极少数微凸体上，导致这些微凸体承受了较大的载荷，极易产生弹塑性变形。

But in the long-term use of the process, it has a few shortcomings, such as the deformation of cement stabilized macadam base become poor, it is easy to crack with the changes in temperature and humidity, the high value of the modulus, high incidence of premature.

但是在长期地使用过程中，水泥稳定碎石基层的变形能力差，在温度和湿度变化时容易开裂：模量值偏高，易发生早期破坏的缺点。

In the frame of deformation quantization, one deals with functions on the phase space, and the star product deforms the commutative classical algebra of observables into the noncommutative quantum algebra of observables.

在变形量子化理论中，物理量依然是函数形式，坐标以及动量的非对易性均体现在函数之间的乘积上。

Because of the Vickers hardness and elongation of Vitallium 2000 and Vitallium 2000 plus are better than traditional dental alloys, so the RPD with Vitallium 2000 has good bending control, deformation rebound and fracture resistance.

Vitallium 2000在材料性能上有所改进，相对传统的常用铸造合金具有支架变形较小、折断的可能性低、卡环较易调改等优点。

The mechanisms summarized are as follows: 1 compressional normal stress;2 ductile and/or viscous deformation in bedding fault since incompetent bed is susceptible to plastic flow;3 higher li.

其机理可归纳为四个方面：1压性的正应力；2以韧性及粘性变形为主，因为非能干岩层易塑性流变；3涂抹效应强；4面理化组构，垂直面理方向的封闭能力大大增强。

For many reasons, such as material, wall thickness, rigidity, clamp etc, during the course of treatment,assemblage and inventory,thin-wall rectangular deep recessed parts tend to generate distortion ,which induces increment of the processing technic establishing difficulty.

由于工件材料、壁厚、刚性、装夹等多种原因，薄壁矩形深腔体零件在加工、装配及库存过程中极易产生变形，导致编制零件加工工艺的难度增加。

These cylinders are protected by Type CG-3 fusible metal plug s with a nominal yield temperature of 212 F.

用标称变形温度212°F的CG-3型易熔金属塞保护这些钢瓶。

These cylinders are protected by Type CG-3 fusible metal plugs with a nominal yield temperature of 212 F.

用标称变形温度212°F的CG-3型易熔金属塞保护这些钢瓶。

If any obstruction, deformation, or extrusion of fusible metal is observed in a pressure-relief device, notify the supplier.

P 如果在减压装置上观察到易熔金属的任何阻塞、变形或突起，通知供应商。

These cylinders are protected by Type CG-3 fusible metal plugs witha nominal yield temperature of 212°F.

用标称变形温度212°F的CG-3型易熔金属塞保护这些钢瓶。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。