英语人>网络例句>时轴 相关的搜索结果
网络例句

时轴

与 时轴 相关的网络例句 [注:此内容来源于网络,仅供参考]

A wire tying tool having a set of movable talons (400, 401) for channeling a loop of hard wire fed from a spool (600) around an object to be tied with a wire knot at high speed; a wire drive (364) with a pullback feature to retract the loop under tension to tighten the loop around the object; a clutch-controlled retractable reel to hold the tension on the wire on the reel; a spinner/cutter that extrudes a knot by turning, kinking and cutting the wire, and then rotating to twist the wire into a knot while drawing the spinner away from the work surface.

一金属丝捆扎工具有一组带有引导从一卷线筒(600)高速传送来的围绕将被一金属丝结捆扎的物体的、硬金属丝环的通道的可运动的爪钳(400,401);一具有回拉功能的以便在拉力状态下回拉此环以拉紧围绕物体的环的金属丝传动(364);一离合器―控制的可回拉的、保持金属丝张力的卷线轴;当旋转器被拉离工作表面时通过转动、扭结和切割金属丝以及然后旋转、以便扭转金属丝形成一结而挤出一结的一旋转器/切割器。

A cylinder containing or inscribed with prayers or litanies that is revolved on its axis in devotions, especially by Tibetan Buddhists.

转经轮,祈祷轮尤指西藏佛教徒所用的滚筒,含有或刻有祈祷文或连祷文,祷告时可绕其轴旋转

When the large rotating arm rotates, the transmission gear is driven to rotate around the fixed gear to rotate the planetary gear, which drives in turn the small rotating arm to rotate in the direction opposite to the large rotating arm, so that the shaft of the small rotating arm reciprocates across the rotation center of the large rotating arm.

当大旋臂旋转时,传动齿轮受到驱动沿固定齿轮周转并带动卫星齿轮转动,卫星齿轮带动小旋臂作与大旋臂反向的旋转,从而使小旋臂上的固定轴随着大、小旋臂的旋转不断往复越过大旋臂的旋心作直线运动。

The front axle is made by traditional recurving I- beam , the second grade fall , with simple manufacturing technique .

前轴采用传统的反弯工字梁,二级落差,经过调质不必进行喷丸处理,制造工艺简单;合理搭配前轮定位关系,使结构紧凑,线条流畅,利于转向操作时轻便灵敏。

At assembly, two hardened 416 stainless steel shafts with splines on the inboard ends are swaged into the brass inner disk to become the upper and lower stems.

在组装时,两个配置腔内端口花键的硬化416不锈钢轴模压在内部为黄铜的阀瓣上,构成上部和下部阀杆。

Each of the first three machines ( V1 , V2 , and V3 ) was provided with only a small rear propeller to blow air at the tail surfaces for steering, but the last machine (V4) had a second propeller mounted co-axially to provide thrust for forward flight when clutched to the compressor motor.

每头三机V1的, V2的,和V3的)提供了唯一的一个小后方转向空气螺旋桨尾吹在物体表面,但最后机(V4区)进行了第二螺旋桨式的合作来提供推力轴为向前飞行时抓住的压缩机电机。

"That is to say, as the rear axle housing, with differential and wheels, moves up and down, the angle between the transmission output shaft changes."

也就是说,当后桥壳随差速器、车轮一起上下运动时,与变速器输出轴之间的角度发生改变,传动轴的长度也随之改变。

After input the reference signal, sine and cosine AC voltage proportional to shaft angle was formed.

采样后经A/D转换和时内部地址总线信号译码,控制轴角数字信号。

At the end of drainage and maturation phases, the auger pushes the curd towards the cutter with rotary disk assembled directly on the shaft of the auger near to the machine outlet; some adjustable knives are assembled on the cutter disk so that it is possible to change the cut thickness.

排放和成熟阶段结束时,螺旋向直接安装在螺旋轴上的转盘切割器推进凝乳,接近机器出口;一些可调整的刀具安装在切割器转盘上,这样它可以改变切割厚度。

In this paper, the performance of a multi-spool axial-flow compressor with a fan during operation with water ingestion is investigated.

摘要本文主要研究了多级轴流风扇/压气机在有水或者其它液相注入时的性能特性。

第55/68页 首页 < ... 51 52 53 54 55 56 57 58 59 ... > 尾页
推荐网络例句

However, as the name(read-only memory)implies, CD disks cannot be written onorchanged in any way.

然而,正如其名字所指出的那样,CD盘不能写,也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口,替代木托盘,免薰蒸,符合欧盟、北美各国对出口货物包装材料的法令要求;喷涂钢托盘适用于重载上货架之用,托盘表面根据需要制作成平板状、波纹状及间隔形式,满足不同的使用要求。

A single payment file can be uploaded from an ERP system to effect all pan-China RMB payments and overseas payments in all currencies.

付款指令文件可从您的 ERP 系统上传到我们的电子银行系统来只是国内及对海外各种币种付款。