英语人>网络例句>时轴 相关的搜索结果
网络例句

时轴

与 时轴 相关的网络例句 [注:此内容来源于网络,仅供参考]

Because of special geometry structure of three-cone bit, the top of formation will form a tri-spine well bottom while drilling with three-cone bit the drill string. It is the tri-spine well bottom that leads to the axial harmonic of vibration when the bit revolves a round and the three concavo-convex heave of bit and formation result in one time (1×rpm),two time (2×rpm), three time (3×rpm) turning table speed.

高岩由于三牙轮钻头的特殊几何结构,钻进过程中在岩层顶部容易形成一个三脊状井底,正是这一三脊状井底,当钻头旋转一周时钻柱轴向三次凸凹变化,由此在轴向产生1倍、2倍和3倍及其更高次倍于转盘转速rpm的谐波振动。

Because of special geometry structure of three-cone bit, the top of formation will form a tri-spine well bottom while drilling with three-cone bit the drill string. It is the tri-spine well bottom that leads to the axial harmonic of vibration when the bit revolves a round and the three concavo-convex heave of bit and formation result in one time (1×rpm),two time (2×rpm), three time (3×rpm) turning table speed.

高岩摘要:由于三牙轮钻头的特殊几何结构,钻进过程中在岩层顶部容易形成一个三脊状井底,正是这一三脊状井底,当钻头旋转一周时钻柱轴向三次凸凹变化,由此在轴向产生1倍、2倍和3倍及其更高次倍于转盘转速rpm的谐波振动。

In addition, the apparatus includes a motor for rotating the shaft to move the dressing stone held by the fixture along an arc centered on the longitudinal axis of the shaft into engagement with the cutting surfaces of the saw when the saw is rotating thereby to remove deposits from the cutting surfaces of the saw.

另外,该设备包括一个马达(18),在锯旋转时,该马达(18)使轴(14)旋转,并沿着一圆弧将由固定器(16)支撑的清理石移动到与锯的切割面接触的位置,上述圆弧以轴(14)的纵向轴线为中心,这样去除在锯切割面上的沉积物。

This portable equipment is suitable for machining precise Reamer Bolt hole needed to connect the large vessel's Engine Shaft, Block, Rudder Stock.

们是韩国大成ENG机械总代理。大型船舶用发动机轴及砧板,是适合舵轴的连接时需要的螺栓孔铰刀精密加工的移动式装备。

Exceptional circumstances arise in the magnetic coupling slip, the sleeve will be in the rapid growth of the eddy heat, the temperature rose sharply, if not in time, will cause magnet demagnetization, so that magnetic coupling failure.

特殊情况下在磁力联轴器出现滑脱时,隔套中的涡流热量会急剧增长,温度急剧上升,如不及时处理,会引起磁钢退磁,使磁力联轴器失效。

By the contact elemen analysis the shrink fit in impeller with shaft of steam turbines, and the contact stress of shrunk-on disc have been investigated.

套装在轴上的叶轮工作时,由于离心力的影响,会使叶轮内孔增大,以至叶轮与轴之间有可能产生间隙,因此,叶轮与主轴配合必须采用过盈配合。

Installation of two outer openings each staggered 180b, the inner and outer openings staggered opening 90b, and pin the three rings with a fixed, outer and inner expansion force in self-expansion force of working together, close to the surface of the pump cylinder run, inflation is not only the axial ring sealed, and the radial seal Ye Hao, it prevents micro-fine sand and into the axial friction pair, can also prevent the micro-fine sand and into the internal voids in the inner ring 3, the operation will not impede expansion ring breathing.

安装时2个外环开口互错开180b,内环开口与外环开口错开90b,并用销钉将3个环固定,外环在自身胀力和内环胀力共同作用下,紧贴泵筒内表面运行,胀圈不但轴向密封好,而且径向密封也好,故阻止微细砂进入轴向摩擦副,也可阻止微细砂进入内环3的内部空隙中,不会阻碍胀圈运行中呼吸。

Note that the rocker arm shaft supporting seat with upper oil hole is at front end of the rocker arm and this end should align with upper oil hole on cylinder head rocker arm shaft when assembling.

应注意,带上油孔的摇臂轴座是摇臂的前端,装配时应注意以这一端和缸盖摇臂轴上油孔对齐。

When a plane wave illuminates the bottom of axicon with ring obstacle, a bottle beam is generated within the maximum non-diffractional distance, and the beam keeps non-diffractional Bessel beam in front and at the back of the Bottle beam.

平面波入射到带有环形障碍物的轴棱锥底面时,将在轴棱锥产生的最大无衍射距离内形成Bottle beam,而在Bottle beam的前后仍然保持无衍射贝塞尔光。

Bearing outer ring and the bearing bore for the tight coordination with the inner shaft to a more loose tie, can be installed on the shaft bearings before.

轴承外圈与轴承座孔为紧配合、内圈与轴为较松配合时,可将轴承先装于轴上。

第19/68页 首页 < ... 15 16 17 18 19 20 21 22 23 ... > 尾页
推荐网络例句

The concept of equivalent rotationally rigidity is offered and the formula of rotationally rigidity is obtained.

主要做了如下几个方面的工作:对伸臂位于顶部的单层框架—筒体模型进行分析,提出了等效转动约束的概念和转动约束刚度的表达式。

Male cats normally do not need aftercare with the exception of the night after the anesthetic.

男猫通常不需要善后除了晚上的麻醉。

Its advantage is that it can be used in smaller units.

其优点在于可以在较小的单位中应用。