时轴

Electron microscope examination showed that the arrangement of axons was disordered and the myelinic membrane denatured and apoptosis was frequently in surgery control eyes, and that the structure of axons was approximately normal in bFGF therapy eyes on the 28th day.

电镜观察可见，28d时，外科对照组轴突排列紊乱、髓鞘变性，多见凋亡现象；但bFGF治疗组轴突内结构尚正常。

Computer Aided Diagnosis Axiography is precise and reliable during the record of condyle movement. On the basis of traditional face bow system, CADIAX use two styli in order to computer the hinge axis; the styli is near to the condyle which diminish the enlargement error and make the record more reliable. Computer technique is adopted by CADIAX, which give a more comprehensive analysis of condyle movement, which can observe the condyle movement in four dimensions. The position of mandible during recording is started from Reference Position, the mandible is posited at a retral position, a more physiological position, and the result is close to reality.

髁突运动轴图描记仪(Computer Aided Diagnosis Axiography)可以准确、可靠的记录分析髁突运动，在传统的面弓记录仪基础上，采用双髁突指针，可以准确计算绞链轴点；测量点与被测髁突距离接近，测量结果更加真实可靠；与计算机技术相结合，数据分析功能更加强大，对髁突运动可以进行四维分析，同步观察双侧髁突的时相特征；记录位置选用参考位置，下颌处于生理后位，记录结果更接近真实情况。

Axis: shorten distance between shafts to postpone the longevity of bearing and mechanism sealing; total seal, non-contacting with medium, rustless; need not adjusting when installation; serialization design, high generalization degree.

轴承体及轴承：拆卸方便，有足够的空间用于维修保养；泵体、泵盖、密封室轴承体浑然一体，精美大方。轴：缩短轴间距，以延长轴承和机械密封的使用寿命；完全密封，不与介质接触，不锈蚀；装配时不需调整；系列化设计，通用化程度高。

Investigation section:Left ventricular long axis,Large-artery short axis,Four cavity heart［Beside sternum,apex of heart,examine arch of aorta in Suprasternal Fossa prorenata］.

探查切面：左室长轴、大动脉短轴、四腔心(胸骨旁、心尖，必要时胸骨上窝探查主动脉弓)。

The one end of bimetal is fixed, the other end is connected to mechanism to drive pointer.

金属片一端固定而另一端与指示轴固定为一体，从而在金属片伸展变形时驱动指示轴旋转并在刻度盘上指示出相应的温度值。

The flexible shafts have better strength and rigidity than ordinary level, they are ideal substitute for conventiona level and universaljoint with such merits as : light weight, good flexibility, easily crooking, compact constru—ction, easily installation, good seal, proof rust and anti—deformation, neatly operation.

工作原理：机械操纵系统中的连接部位受力位移时，软轴的芯轴受力，产生往复运动，形成拉力、推力驱使机械作换挡、取力、升降、行走、加油、熄火、制动、转向、换向等工作，它不但优于一般杠杆的强度、刚性而且重量轻、柔性好、可弯曲、结构紧凑、安装方便、密封性好，不易锈蚀变形，操作轻便灵活，是替代传统的连杆、万向节机构的理想产品。

According to the characteristics of the larger start electric curent, start torque and the demagnetizing influence of the armature reaction of motereycle starter at the moment of starting, the formula of the largest demagnetizing magnetic- power is deduced and the magnetic method of separehng alnico is gnined on the basis of the largest dernagntizing magntic - power.

根据摩托车起动电机起动电流大、起动转矩要求高的特点，以及起动时直轴电枢反应和交轴电枢反应对永久磁铁的去磁作用，推导出最大去磁磁势的计算公式，给出了根据最大去磁磁势选择磁钢的方法，并通过实测证明电枢反应对起动电机性能的影响。

When two axes make the synchronized reverse rotation, on each instantaneous two axis eccentric qualities produce the centrifugal force of inertia, always mutually counterbalances along x-x force component, but always mutually superimposes along Y-Y force component, this has formed the sole this direction simple harmonics strength.

两轴作同步反向回转时，每一瞬时两轴上偏心质量所产生的离心惯性力，沿x-x方向的分力总是互相抵消，而沿Y-Y方向的分力总是相互叠加，这就形成了单一的该方向的简谐力。该力作用在筛箱上，驱动筛箱作轨迹为直线的往复振动。

For diameter 26mm axle bar of CK45 steel,when surface hardness is 54～ 62HRC,core maximum hardness is 32HRC and case depth is 3.8～5.3mm,it has an optim um combination of strength and ductility .

对φ26mm CK45钢轴杆，当表面硬度为54～62HRC，硬化层深度为3.8～5.3mm，心部硬度＜32HRC时，轴杆具有最佳的强韧性，获得了较高的静扭强度和扭转疲劳寿命。

And in this process the torsional rigidity of the cross axle type universal shaft was found having great impacts on the torsional vibration of the main transmission system.

在进行轧机主传动系统的扭振分析时，发现十字轴式万向联轴器的扭转刚度对主传动系统扭振的影响十分巨大。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。