英语人>网络例句>斜面 相关的搜索结果
网络例句

斜面

与 斜面 相关的网络例句 [注:此内容来源于网络,仅供参考]

After that, select Bevel and Emboss and just follow the image below.

在此之后,选择斜面和浮雕,只是按照以下的形象。

Bevel Gears are the most versatile in that they have good efficiency.

斜面齿轮执行机构具有最广泛的用途和良好的操作效率。

The items in both Figure 6-8 and Figure 6-9 do not include a bezel.

在图6-8和图6-9里的按钮都没有斜面

Blossom to make a flower can long, when cutting branch extraction a flower, cut had better cut 45 degrees cant, can enlarge bibulous area so, OK also the flower cauline radical ministry is knocked crack, will help bibulous.

为了让花能长时间绽放,在切取花枝时,切口最好削成45度的斜面,这样可以扩大吸水面积,也可以把花茎基部敲裂,来帮助吸水。

But what is this incline that is indicated by Mr. Louis Blanc?

但是路易斯·勃朗所指出的这种斜面是什么呢?

To start off, we're going to look at the butt end of the racket handle. The handle has eight sides, also called "bevels," and the topmost bevel is Bevel 1. Bevels 2, 3, 4 etc. follow going clockwise around the handle. Bevel 5 is located on the "bottom" of the handle.

首先我们观察拍柄的平头端,拍柄有八面,也就是八个斜面,最上面的标记为1,然后顺时针方向是2,3,4等等,底5面试拍柄的最下面的一个面。

Realistically designed as a floral spray, the two flower-heads set with oval cabochon rubies within an undulated border of brilliant cut diamonds, the stem set with baguette diamonds, the leaves with eight and brilliant cut diamonds.

栩栩如生的花束造型,两朵花的花瓣镶嵌椭圆形鹅蛋红宝石,波浪形边缘镶嵌明亮切割钻石,花茎镶嵌长方形钻石,叶子镶嵌八斜面及明亮切割钻石

This design is to dials forks the components the processing craft and the jig design, its components are the forging, has the volume to be small, components complex characteristic,Because the surface is easier than the hole to process, when formulation technological process, first the machined surface, then processes other take the surface as the datum,In which various working procedures jig all uses the unit clamp, special regarding processes the big end of hole, the trough and drills the capitellum hole incline eyelet in the working procedure, Chooses locate mode which two sells at the same time, and operates the simple manual clamp way clamp, its organization design is simple, the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计,其零件为锻件,具有体积小,零件复杂的特点,由于面比孔易加工,在制定工艺规程时,就先加工面,再以面为基准来加工其它,其中各工序夹具都采用专用夹具,特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中,选一面两销的定位方式,并以操作简单的手动夹紧方式夹紧,其机构设计简单,方便且能满足要求。

This design is to dials forks the components the processing craft and the jig design its components are the forging has the volume to be small components complex characteristicBecause the surface is easier than the hole to process when formulation technological process first the machined surface then processes other take the surface as the datumIn which various working procedures jig all uses the unit clamp special regarding processes the big end of hole the trough and drills the capitellum hole incline eyelet in the working procedure Chooses locate mode which two sells at the same time and operates the simple manual clamp way clamp its organization design is simple the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计,其零件为锻件,具有体积小,零件复杂的特点,由于面比孔易加工,在制定工艺规程时,就先加工面,再以面为基准来加工其它,其中各工序夹具都采用专用夹具,特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中,选一面两销的定位方式,并以操作简单的手动夹紧方式夹紧,其机构设计简单,方便且能满足要求。关键词拨叉,加工工艺,专用夹具,设计

In some makes of engine the helically splined coupling is not used and the angular displacement of the shafts is effected by centrifugally actuated devices of the swinging link or inclined plane type.

在一些发动机的制造中,并不使用螺旋式花键套管,通过摇杆或斜面型的偏心操纵装置,曲轴相位角起到同样作用。

第5/25页 首页 < 1 2 3 4 5 6 7 8 9 ... > 尾页
推荐网络例句

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47:5 法老对约瑟说,你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法,同时,采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。

Hey Big Raven, The individual lies dont matter anymore - its ALL a tissue of lies in support of...

嘿大乌鸦,个别谎言的事不要再-其所有的组织的谎言,在支持。