斜度

Rytz Method ; maximum oblique line ; Right-angled Triangle Method ; plane figure ; projection plane ; dip angle ; conjugate diameter

里茨作图法；最大斜度线；直角三角形法；平面图形投影面；倾角；共轭直径

In the design,the optimum radius of the rear convex mirror was presented which could efficiently compensate the effect of thermal lens,and the resonator would become a equivalent stable resonant operation dynamically. A slope efficiency of 13% and beam divergence of 1.3 mrad were achieved.

选择的凸面全反镜的最佳曲率半径有效地补偿了增益介质热透镜效应，激光器实现了动态稳腔运转，激光脉冲能量输出斜度效率大于13%，光束发散角优于1.3 mrad。

The factor analysis draw out 5 factors: variability, crudity, size, rake and hasty.

因素分析抽出5个因子：变异性、生硬性、大小、斜度、潦草程度。

For applications with pitches below 0.5 mm, choices are limited to laser cutting or electroforming.

组件斜度和孔密度也表明要选择适当的制造技术。

Flat-roofed buildings may have dome d skylights; in others the skylight follows the slope of the roof.

平坦屋顶的建筑物可能有半球型的天窗，而在其它建筑物中，天窗则可随着屋顶的斜度变化。

Flat-roofed Buildings may have domed skylights; in others the skylight follows the slope of the roof.

平坦屋顶的建筑物可能有半球型的天窗，而在其它建筑物中，天窗则可随着屋顶的斜度变化。

The wood of China fir and Taiwan zelkova were used for cutting test. Cutting conditions of the tool were rake angle 35°, sharpness angle 29° and clearance angle 26°. Five depths of cut were laboratory fraise for metal cutting. The cutting force measurements, based on the cutting surface of the test material, were performed by a quartz piezoelectric three component dynamometer.

采用杉木与台湾榉之气乾材为试验材料，切削试验以高速度钢材质之平刀进行二次元纵切削(90-0)之平削试验，切削条件中刀具斜度角为35°，刀端角为29°，余隙角为26°，切削深度为0.05、0.1、0.2、0.3与0.5 mm，切削速度为1.1cm/s。

But the introduction of new basis functions also poses a new problem, that is, the complexity of computation of two matrixes' elements in the derivative generalized eigenvalue problem in NMM. Fortunately we found a recursive algorithm and solved it concisely.

在引入幅度基函数和斜度基函数后，广义特征值问题中矩阵元素的计算变的繁琐，我们运用一种递推算法简洁地解决了这个问题。

69 Years. Refractive error, axial length, anterior chamber depth, lens thickness, corneal curve , heterophoria were examined at 6-month intervals.

每6个月检查一次，检查内容有近视屈光度、眼轴长度、角膜曲率、前房深度、晶状体厚度、隐斜度。

In this paper, the 3D finite element method (3D-FEM) is employed to calculate the responses of the dual-laterolog in the high angle deviated wells. Moreover, under the consideration of the impracticability of the strict 3D inversion of the electrical logging, one method named the fast deconvolution, is given to correct the electrical logs which is calibrated by the forward method, 3D-FEM.

在考虑常规双侧向测井和正演数值模拟计算的基础上，利用三维有限元素法（3D-FEM）进行大斜度井中双侧向测井响应的数值模拟求解，并以不同倾角为条件验证了方法的有效性；进一步针对目前严格的电测井三维反演处理的不现实性，应用严格正演刻度下的快速反褶积处理方法进行定向井的电测井曲线校正。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。