数学公式

In order to make the uncertainty of the dose index measurement in the head phantom reasonable for the medical diagnostic X-ray radiation sources of the computed tomography, the measurement uncertainty components were analyzed according to the mathematical model for the computed tomography dose index test method with a 100 mm ionization chamber.

摘 要：为了使医用诊断计算机断层摄影装置X射线辐射源在模体中的剂量指数测量结果的不确定度评定合理，基于用带有100 mm长杆电离室的积分剂量仪测量CT剂量指数的数学模型，对其测量不确定度来源进行分析，列出了方差、灵敏系数及标准不确定度的计算公式，从而给出了CT剂量指数测量的合成标准不确定度和扩展不确定度。

In this paper,the general mathematic model and equivalent circuit of dual stator-winding induction machine are proposed.

首先给出了定子双绕组异步电机通用数学模型及等效电路，采用解析法对不同绕组结构的定子双绕组异步电机漏电抗计算进行了系统地分析，导出了相应的计算公式。

Firstly, according to the analysis of the forming principle of the involutes profile and the tooth thickness of formula, a mathematical model of involutes profile was established.

首先，根据对渐开线齿廓形成原理和渐开线齿轮任意圆上的齿厚公式的分析，建立了插齿刀的渐开线圆柱齿轮齿廓的数学模型。

Meanwhile, the Beer-Lambert equation was modified for 254nm and 365nm UV light permeation through methyl orange solution, and a mathematic equation for light permeability was established.

通过实验研究，对紫外光在溶液中透过性的Beer-Lambert公式进行了修正，得出了不同波长紫外光在甲基橙溶液中透过性的数学表示式。

Mathematics model of hysteresis loops and calculation formula of hysteresis energy for Masing and non-Masing material were established.

本文针对我国广泛使用的16MnR压力容器用钢焊接接头，从焊接接头材质和力学不均匀性的实际出发，首次分别系统地对焊缝、热影响区和母材进行了低周疲劳实验研究，求得各分区的循环滞回环及其特征参数，建立了Masing材料和非Masing材料的滞回环数学模型和滞回能计算公式。

D models are the most widely spread in the world of turbo-machinery for its simplicity, but they are indeed purely empirical correlations which not only fail to provide detailed information inside one or more components, but also require significant effort to recreate themselves if engine operating conditions or component representations change; quasi 3-D models have been the workhorses for compressor and turbine design for many years, and the primary benefit of using quasi 3-D system models is to facilitate the design and detail analysis of a particular component across the range of possible boundary conditions; Full 3-D models are gradually replacing quasi 3-D ones by virtue of requiring no exit flow angle model and loss model and being capable of predicting secondary flow in cascade.

零维模型由于使用时简单易行，因此在涡轮发动机的仿真中得到广泛应用，但零维模型作为纯粹的经验关系式无法反映部件内部的流动细节，并且一旦部件有少许改动则新特性的建立耗费巨大；准三维模型由于能够详细地提供部件内部的流动情况，方便设计而成为涡轮和压气机设计的主要工具；全三维数学模型正逐步取代准三维模型在涡轮设计中的主导作用，同后者相比前者能够预测叶轮机械内的二次流动，在粘性流计算时不需要气流角和损失的经验公式，因此拥有巨大的发展前景。

Based on the linear wave resistance principle,the wave resistance formula was established for the high speed trimarans with a main center hull and two small outer hulls.

本文据线性兴波阻力理论推导了辅船体与主船体水下体积不相等情况下的兴波阻力计算公式，据此以数学船型作为片体对高速三体船片体兴波干扰规律、兴波阻力曲线规律进行了研究，并采用简单枚举与等值线图谱相结合的方法对片体布局优化问题进行了探讨。

The method of defining pedestal pile foundation deformation modulus is especially discussed in this article, and it takes the Mindlin solution as the starting point using mathematics method to get the Poissons ratio which is the factor influencing foundation soil deformation modulus , and a deformation modulus calculating equation is finally determined.

其中特别论述了扩底桩地基变形模量的确定方法，并从Mindlin解出发利用数学方法得出了影响地基土变形模量大小的因素—泊松比μ，初步确定了比较完善的变形模量计算公式。

According to t he refined D-InsAR functional model some basic D-InSAR models have been derived, such as two-pass, there-pass and four-pass method. Some concise error analyses have al so been give during the derivation.

根据完善后的数学模型，推导了差分干涉测量基本的两轨、三轨、四轨算法的模型公式，并对其中的误差源进行了相应的理论分析。

According to the principles of tooth meshing and manufacturing helicoi ds, a mathematics model is constructed to reflect the manufacture process of nut , and the formula of the grinding wheel section is developed. The parameters of the section are obtained through numeral arithmetic; moreover the parameters of the dresser are worked out. Based on these work, the solid model of the ball scr ew nut, grinding wheel and tooth dresser are developed in the Pro/E software, wh at's more, the process of the dressing...

根据螺旋面加工原理、齿形啮合原理及回转面砂轮加工螺母工艺建立了相应的数学模型，并推导出砂轮截形的计算公式；采用数值计算方法求解砂轮截形参数，进一步得到修整器靠模板的参数；在此基础上，利用Pro/E软件对大导程滚珠丝杠螺母、砂轮和砂轮修整器进行了实体建模，并对砂轮的修整过程和螺母的加工过程进行了运动仿真，有效地验证了砂轮截形的计算结果。

Singer Leona Lewis and former Led Zeppelin guitarist Jimmy Page emerged as the bus transformed into a grass-covered carnival float, and the pair combined for a rendition of "Whole Lotta Love".

歌手leona刘易斯和前率领的飞艇的吉他手吉米页出现巴士转化为基层所涵盖的嘉年华花车，和一双合并为一移交&整个lotta爱&。

This is Kate, and that's Erin.

这是凯特，那个是爱朗。