数值技术

Based on the theoretical analysis for 1000 m long drainage skills, the UDEC4.0 numerical simulation software is adopted to perform the calculation, showing that the height of caving zone and fractured zone of gob is 9 m and 30 m, the vertical height from the mining induced O-shaped circle to the roof is 10~25 m, and the horizontal distance to both sides of gob is 10~35 m.

本文在顶板千米钻孔抽采技术原理分析的基础上，采用UDEC4.0数值模拟软件计算得出采空区冒落带和裂隙带高度为9m和30m，采动裂隙&O&形圈的范围为距工作面顶板垂高10~25m，距采空区两侧水平距离为10~35m。

Based on the first derivative value of band at sensitive wavebands, the linear function model was established. R^2 of 0.7818 and 0.5899. This research shows that chlorophll in formation of reflecting apple growing status can be preciously obtained by using hyperspectral remote sensing.

基于敏感波段的微分数值；建立了一阶微分光谱值与苹果叶片SPAD值和叶绿素含量的回归模型；确定系数分别达到0.7818和0.5899；为利用高光谱遥感技术反映苹果生长状况的叶绿素信息提供了依据。

Based on unsteady N-S equation of three dimensional and compressible viscous fluid, the aerodynamic performance for the fast special container flat wagon at the speed of 160 km/h was calculated numerically by adopting the technology named slippage grid.

摘 要：利用三维、可压、非定常N-S方程，采用滑移网格技术对我国正在研制的160 km/h快速集装箱专用平车与动车组分别在明线和隧道内会车时的气动性能进行数值模拟。

That number, rounded down, is the number of techs you can fully research at once.

这个四舍五入的数值表示你当前可以全速研究的技术项目的数目。

Aiming to a method for the synthesis of silicon nitride powder by direct nitridation process based on fluidization technology, a two-dimensional mathematical model of thermal process in a suspended bed was established, the thermal process was simulated based on the commercial CFD software FLUENT, and the effects of the flow velocity of nitrogen gas, the ratio of particle to gas and nitridation temperature on the temperature of the bed and the conversion rate of silicon were analyzed.

针对基于流态化技术利用硅粉直接氮化合成氮化硅粉的新工艺，建立了悬浮床内热过程的二维数学模型，并借助CFD商业软件FLUENT对悬浮床内热过程进行了数值模拟，分析了氮气速度、粉气比和氮化温度等因素对温度场和硅转化率的影响。

Barlat1989 is recommended owing to its computational effectiveness. The technique is given using the dynamic relaxation method to obtain the steady position of the blank inside die opening line from end of holder forming stage to start of die forming stage.

在板料成形过程的数值模拟研究中，提出了将动力松弛法用于获得压边圈成形结束到凸模成形开始之前凹模开口线内板料的稳定位置，从而消除动力效应的处理技术。

In order to determine the optimal shape of interchamber pillars,seven models are established using finite element numerical simulation technique to study the influence of different orebody dip angles and different intersection angles between the normal lines of pillar wall and ore bed on pillar strain and stress .

本文采用有限元数值模拟技术，建立了七种模型，计算分析了不同矿体倾角及矿柱壁面与矿层面法线夹角的变化对矿柱应力应变状态的影响，从而确定出最佳的矿柱形状。

Parameters of movement process of saltating sand grains The thesis studies some motion parameters of saltating sand grains by using wind tunnel experiment and computer simulation.

沙粒跃移运动参数利用风洞实验与计算机数值模拟技术，研究了跃移沙粒运动参数。

This thesis reviewed the historical development, the current taxonomic status and the phylogeny of rhizobia, and compared the main methods applied in rhizobial polyphasic taxonomy.

本论文综述了根瘤菌的分类现状、系统发育地位及有关的研究方法；采用数值分类、16S rDNA PCR-RFLP、BOX-PCR、AFLP、16S rDNA 序列分析、G+Cmol%测定、DNA-DNA同源性分析等多相分类技术对分离自我国不同地区的木本豆科植物刺槐、黄檀、合欢根瘤菌进行了系统地分类学上的研究。

Combined with dumm y damping parallel circuit,the voltage prediction can eliminate partially the sam pling tim e delay of input and output data transfer thus resulting in current noise reduction and a numerical stability im provement,which can achieve an overall simulation stability in steady and transient states .

利用电压预测技术，结合&虚&阻尼并联支路，可以有效地减小接口电流噪声，提高 RTDS数值计算稳定性，保证数模接口在稳态和暂态仿真中的稳定。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。