数值分析

The forming process for warm extrusion punch of drilling bit shell was simulated with contact analysis modules in ANSYS.

中文摘要：运用有限元分析软件ANSYS的接触分析，对钎头壳体温挤压凸模进行了数值模拟。

3D FEM has been employed to analyze and simulate numerically the process of hot extrusion of transmission shaft forgings with deep research of phenomena of top and bottom of fork that not completely filled in the forming process hence all especial punch die structure preventing the defects been developed.

新闻摘要：采用三维有限元法对套管叉锻件热挤压成形过程进行了数值模拟仿真分析。针对其成形过程中出现的叉部顶端及底端充不满现象进行了深入分析，提出了防止缺陷产生的一种特殊的凸模结构。

By a simulation with numerical computing to the grab bucket failure from heavy deformation under load, this paper gives an advice to improve the grab according to the analvzed result.

对抓斗受力后发生严重变形而失效的工况进行数值模拟仿真计算，根据分析结果提出改进措施，并在同样的工况下对修复方案进行仿真分析，为抓斗的修复工作提供技术支持。

The heat-producing power of weapon-grade plutonium, weapon-grade uranium and depleted uranium per kilogram were calculated through simulation and dynamic decay cascade, the regression line was fitted and analyzed. The temperature fields of the nuclear explosive device raised by Steve Fetter were analyzed according to the simulation results of the heat-producing power of the exothermic materials. The hypothetical models of the nuclear explosive device were modified according to the normal disposal method in industry manufacture, and thermal stress distribution was simulated with the information processed before.

通过级联衰变动力学计算得到每千克武器级钚、武器级铀及贫化铀的放热功率，并对仿真结果进行拟合分析；选取其最大值对Steve Fetter提出的公开核装置假想模型进行温度场数值仿真；根据工业生产实际对Steve Fetter提出的公开核爆炸装置假想模型进行修订，并对其进行热应力仿真分析。

On the basis of these induced equations, the munerical computation and analyzing are completed, especially for the analyzing and computing the character of helix angle and tooth profile in different section for worm and stator which determines manufacturing for the parts of this kind of drive.

在啮合公式推导的基础上，对超环面行星蜗杆传动的啮合特性进行了数值计算和分析，特别是对与加工、制造这种传动蜗杆和定子紧密相关的蜗杆与定子的螺旋升角及其各个截面的齿形进行了深入的分析与计算。

Stability of 14 high-cut slopes in Guangdong province is analyzed with typical rock mass structure analysis method and stereographic projection method, and with the numerical simulation method UDEC this paper simulated the excavation and reinforcement courses of the important slopes. Some conclutions and suggestions are based the analysis above.

本文结合广东某省道沿线14个高陡岩石边坡的开挖和支护方案的选择设计，运用常用的岩体结构分析方法和赤平投影方法对边坡的稳定性进行了分析，采用UDEC数值模拟方法对一些重点边坡的开挖支护进行了模拟，得出了以下一些结论： 1、边坡支护形式的选择应遵循&安全绿色、水土保持、恢复自然、环保之路&的设计原则。

According to the standard and request of mechanical structures for electronic equipment tests, the finite element model of the electronic equipment cabinet was built by using the software of finite element analysis-ANSYS and simulated the tests of random vibrations by loading and calculating. The 3-D isopleths graph of deformation and stress of the cabinet was obtained. It could confirm the maximum of deformation and stress of the cabinet and probability of occurrence. Through more analysis of the frequency response curve reflected directly and clearly the deformation of the cabinet within the particular seismic frequency.

根据电子设备机械结构随机振动试验的标准和要求，采用有限元分析软件ANSYS建立电子设备机柜结构的有限元模型，通过加载求解对其进行随机振动试验的数值模拟，得到机柜有限元模型的三维变形和应力等值线图，进而确定机柜承受应力和变形的最大值及发生概率；通过对频率响应曲线的进一步分析，可以直观明了地反映出机柜承受一定频率范围地震下的变形情况。

At last, examples of an S-band and a C band klystrons is calculated by disk model under field distributing of analytic value and numerical data, and the motion and output energy are also analyzed.

以S波段和C波段大功率速调管为例，用分析场和数值场分别带入圆盘模型，对运动过程和输出能量进行了分析。

The cutoff conditions of metal-clad waveguides or loss dielectric waveguides are discussed. The effects of metal-cladding on the cutoff condition of graded index waveguides are analyzed at first. The principle of cutoff intensity modulator has discussed in detail.

本文首次提出一种适合于分析含金属覆盖层的均匀和渐变介质波导在截止点附近的光学特性的近似的解析方法，并对金属覆盖层的均匀阶跃介质波导在截止点附近的模传播特性作了全面的分析，所得到的结果同精确的数值解结果相吻合。

By careful study to the deflection response of a hinged-fixed circular plate u nder concentrated impulse loading,the saturated impulse phenomenon in the proces s of response is discussed.

利用有限变形弹塑性连续体的最小加速度原理，建立了分析圆板动力响应问题的数值方法，并通过对均匀分布的脉冲载荷作用下铰支圆板位移响应的细致分析，探讨了响应过程中的饱和冲量现象，指出对于高载范围内的脉冲载荷，相应于最大变形的饱和冲量确实是存在的。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。