数值分析

To investigate the thermal protection effects of a heat sinking vest with phase-change material in high-temperature and high-humidity environment and the feasibility of numerical computation of heat transfer to the vest,based on the analysis of heat and mass transfer characteristic about the accouterments,a thermodynamic model was set up with the enthalpy method.

为了研究相变材料降温服在高温高湿条件下的热防护性能和相变材料数值计算方法应用于降温服传热计算的可行性，在分析服装传热传质特点及计算方法的基础上，利用焓值分析法对服装中的相变材料建立传热模型，在整个区域建立统一的能量方程，在区域结点进行离散，并进行隐式求解，得到焓的分布。

However, the mechanics of soft tissue is the critical in influencing the whole plantar pressure. We use an instrument to measure the load and displacement relationship of heel pad that development by our laboratory to measure mechanics of soft tissue in order to approach approximately to the experiment data. Then make use of the curve fitting to obtain material parameter that necessary of analysis. Finally, the result and experiment will be verified.

而软组织的力学性质是影响整体足压大小的关键，为了使研究的分析结果更接近实验数值，软组织力学性质量测利用实验室所开发的软组织力量位移量测器取得，再利用曲线模拟的方式得知分析所需材料参数，最后将分析所得结果与实验进行验证。

The above problems are studied in this thesis. First, the implicit NND scheme with mix flux splitting method proposed by Zhang Hanxin that is first order accurate in time and second order in space is modified. The modified scheme keeps the characteristics of fast convergence and is second order accurate both in time and space. It can be capable of simulating the unsteacly flow. Second, the topological method founded by Zhang Hanxin is improved to study the characteristics of vortex near the singular point on its axis and the cross streamlines on the longitudinal section passing the vortex axis. On the basis of topological results, a program which visualises numerical results is made out. It can help us analyse the characteristics of vortex motion.

本文对上述问题做了研究：第一，在数值模拟方面，借助于张涵信提出的NND算法和混合通量法，我们将他建立的时间为一阶、空间为二阶精度的快速隐式算法推广为时间和空间均为二阶精度的算法，这样做保留了原格式收敛快的特点，而且能适用于真实的非定常流态的计算；第二，将张涵信的拓扑分析方法加以推广，研究了涡轴附近及破裂点邻域内流场的空间特征，并以这些拓扑分析结果为指导，研制了一套显示计算结果的软件，这一软件能很好地帮助我们分析流场的计算结果和旋涡演变的特征。

Regarding a tractive elevator as example, according to the drawing and measurement of its parts, and computing with Ansys, its dynamic parameters are obtained, which are used in analysis of horizontal direction vibration with Matlab.

第五章，在电梯数值计算模块的基础上，开发了电梯动态特性仿真平台，并用来进行电梯各种工况下模态分析、谐响应分析、瞬态动力学响应分析。

Firstly, based on the sliding mode control and backstepping technique, a new attitude tracking controller is derived to control the attitude motion of spacecraft, the stability of the system is analyzed via Lyapunov method and the reaction wheel dynamics is also considered from the real applications point of view. The whole design process is divided into two steps: the first step is to use sliding control technique to design suppositional adaptive variable structure controller; and the second step is to design attitude tracking controller based on SMC and backstepping technique. Numerical simulations are performed to show that both tracking maneuver and vibration suppression can be accomplished effectively.

首先，采用自适应后步法结合主动振动控制技术设计了姿态跟踪鲁棒控制器，基于Lyapunov方法分析了系统的渐近稳定性；在此基础上，显性地考虑了执行机构动态特性问题，将整个设计过程分为两个步骤：第一步采用滑模控制技术设计了变结构虚拟控制器，给出自适应控制律的设计方法；第二步，将后步法与滑模控制技术相结合，设计了姿态跟踪鲁棒控制器，给出飞轮电压的输入算法及稳定性分析；最后，将提出的控制方法应用于挠性航天器的姿态跟踪控制，通过数值仿真对所提方法的可行性与有效性进行分析和验证。

At the beginning of the thesis, the structure of usually used radome is introduced and the parameters of electromagntic characters are described in Chapter Ⅰ; the different methods for analysis of the electromagnetic characters of radome are summarized in Chapter Ⅱ; the propagation of 3-D beam in free space is conducted in Chapter Ⅲ; then in Chapter Ⅳ, the 3-D Complex Ray Theory are analyzed and the characters of transmitted field of sum and difference beams through radome are studied, and the relative formulations of calculation are rekened; at last the electromagnetic characters of the ellipsoidal sandwich radome and the plane single-layered radome are discussed, and suggestions for optimization of electromagnetic properties of radome are given.

本文第一章介绍了常用雷达罩的结构和描述雷达罩电磁特性的参量，第二章概述了目前分析雷达罩电磁特性所采用的各种方法，第三章分析了三维波束在自由空间传输特性，第四章研究了三维复射线理论，并应用它分析了单脉冲和差波束穿过雷达罩透射场的特性，导出了有关计算公式，在第五章，通过大量的数值计算和实验研究，讨论了椭球形三层夹心状实用雷达罩和单层介质平板模拟雷达罩的电磁特性，并提供了雷达罩电气特性优化的建议。

Numerical simulation of flexible end-plates connections and fin plate shear connections under fire was successfully done using FEM software ANSYS. Geometric, material and contact non-linearity was taken into account.

利用有限元分析软件ANSYS对高温下内缩式端板连接和柔性剪力板连接进行了数值模拟分析，分析中考虑了材料非线性、几何非线性及接触非线性等多种非线性因素的影响。

Such parameters as the percentage of ordinary reinforcment, amounts and configuration of unbonded prestressed tendons, the ratio of span to depth and the loading patterns were considered. Based on the results, the fomula for the eqivalent length of deformation zone on the beams at ultimate were developed. A simple formula was developed for the ultimate mid-span deflection of concrete beams with concept of equivalent length of deformation zone, and the deformation of beam before internal reinforcement yielding was predicted by the traditional formula for the deformation of partically prestressed concrete beam. Then an analytical model was deduced for analyzing the ultimate stress increment in those concrete beams prestressed with external or internal unbonded tendons based on the mid-span deflection.(4) Testes were carried out on a thin-walled concrete box beam presressed with external CFRP tendons to study its short-term performances under uniform load, long-term behaviors under uniform load, and full-time performance under four-point load in turn.

3以体内非预应力钢筋配筋率、体外预应力筋配筋率、体外预应力筋布置形式、预应力度、跨高比、荷载形式等为参数，用非线性分析程序对体预应力筋混凝土梁进行了参数分析，依据分析结果提出了以综合配筋指标和预应力度为参数的等效变形区长度的计算公式，进而提出了基于等效变形区长度的极限挠度计算公式；体内非预应力钢筋屈服前的挠度计算采用常用的部分预应力混凝土梁挠度计算公式；依据试验和非线性数值计算结果，将不同转向块布置形式的体外预应力混凝土梁简化为跨中一个转向块的体外预应力混凝土梁，推导了基于跨中挠度的体外预应力筋应力增量的简化计算公式。

Such parameters as the percentage of ordinary reinforcment, amounts and configuration of unbonded prestressed tendons, the ratio of span to depth and the loading patterns were considered. Based on the results, the fomula for the eqivalent length of deformation zone on the beams at ultimate were developed. A simple formula was developed for the ultimate mid-span deflection of concrete beams with concept of equivalent length of deformation zone, and the deformation of beam before internal reinforcement yielding was predicted by the traditional formula for the deformation of partically prestressed concrete beam. Then an analytical model was deduced for analyzing the ultimate stress increment in those concrete beams prestressed with external or internal unbonded tendons based on the mid-span deflection.(4) Testes were carried out on a thin-walled concrete box beam presressed with external CFRP tendons to study its short-term performances under uniform load, long-term behaviors under uniform load, and full-time performance under four-point load in turn.

3以体内非预应力钢筋配筋率、体外预应力筋配筋率、体外预应力筋布置形式、预应力度、跨高比、荷载形式等为参数，用非线性分析程序对体预应力筋混凝土梁进行了参数分析，依据分析结果提出了以综合配筋指标和预应力度为参数的等活动房效变形区长度的计算公式，进而提出了基于等效变形区长度的极限挠度计算公式；体内非预应力钢筋屈服前的挠度计算采用常用的部分预应力混凝土梁挠度计算公式；依据试验和非线性数值计算结果，将不同转向块布置形式的体外预应力混凝土梁简化为跨中一个转向块的体外预应力混凝土梁，推导了基于跨中挠度的体外预应力筋应力增量的简化计算公式。

Based on the data analysis and numerical simulation, the Arctic sea ice climate variability was researched, the result were as following:(1) The analysis on the seasonal cycle of the Arctic Ocean and atmosphere showed that: The seasonal surface wind is somewhat trade wind like in some regions in the Arctic. The surface air temperature is robustly determined from the underlying environments such as sea ice and Greenland glaciers. In the sea ice region the precipitation rate is larger than that of evaporation. Furthermore, the Arctic Ocean hydrology is profoundly influenced by the surrounding rivers discharge. These are the decisive factors on the ocean salinity pattern. Sea ice flux through the Fram Strait is larger in winter than in summer. From the 40s in the 20th century on, the ice volume flux has an increasing trend. The Arctic rivers flood season is about the melt period, the winter rivers discharge has a significant increasing. Correlation analysis shows that 7 to 10 years is a characteristic time scale that rivers discharge leads Fram Strait ice volume export.(2) Considering 9 major arctic rivers, the Arctic Ocean circulation was simulated through BOM. The result shows that: The BOM can reproduce the main Arctic Ocean circulation pattern. The"Islandization"which is commonly used in OGCMs to treat the North Pole, not only influences the ocean current near the pole, but also influences the current in the Northern Atlantic Ocean, thus the bogus island might influence global climate through thermohaline circulation in the Atlantic Ocean.

在资料分析和数值模拟的基础上，对北极海冰的气候变率进行了深入的研究，结果如下：(1)对北极地区大气和海洋季节循环特征的分析表明，气候平均风场在部分地区具有&信风&的性质；而气温场与海冰分布及格陵兰半岛冰原的下垫面特征有密切关系；在北极海冰区的降水量大于蒸发量，并且在全球大洋中北冰洋受到河流径流的影响最大，对北冰洋的盐度分布有决定作用；通过弗瑞姆海峡的海冰通量在冬半年大于夏半年，并且从20世纪40年代起，海冰的体积输送有增加趋势；北极河流的汛期主要在融化季节，冬季的河流流量有显著增加的趋势；相关分析表明7到10年是北极河流流量影响弗瑞姆海峡海冰体积输送的一个特征时间尺度；(2)采用BOM海洋模式对北冰洋海洋环流进行了模拟研究，在模式中考虑了北极9条主要河流的作用，结果表明该海洋模式可以较好模拟出北冰洋海洋环流的基本特征；多数大洋环流模式采用&北极岛化&的方法处理北极点，模拟结果表明&北极岛化&不仅影响到极点附近的海流，还会对相对较远的北大西洋海流造成影响，并可能通过大西洋的热盐环流对全球气候产生影响；(3)采用CSIM4海冰模式对北极海冰的气候态进行了模拟。

We have no common name for a mime of Sophron or Xenarchus and a Socratic Conversation; and we should still be without one even if the imitation in the two instances were in trimeters or elegiacs or some other kind of verse--though it is the way with people to tack on 'poet' to the name of a metre, and talk of elegiac-poets and epic-poets, thinking that they call them poets not by reason of the imitative nature of their work, but indiscriminately by reason of the metre they write in.

索夫农 、森那库斯和苏格拉底式的对话采用的模仿没有一个公共的名称；三音步诗、挽歌体或其他类型的诗的模仿也没有——人们把&诗人&这一名词和格律名称结合到一起，称之为挽歌体诗人或者史诗诗人，他们被称为诗人，似乎只是因为遵守格律写作，而非他们作品的模仿本质。

The relationship between communicative competence and grammar teaching should be that of the ends and the means.

交际能力和语法的关系应该是目标与途径的关系。