数值

The velocity distribution of jetting penetrator charge under different initiation ways was s tudied by theoretical analysis. The numerical simulation results coincide with the theoretical analysis, a practical method of numerical simulation and material model parameters were obtained.

并通过理论分析研究了不同起爆方式下所形成的杆式射流的速度分布，数值模拟结果与理论分析吻合较好，得到了一套实用的数值模拟方法及材料模型参数。

To enter a value in percent format, type a percent sign after the value.

在输入数值后键入%，输入的数值将套用百分比样式。

Then, we use numerical continual method to get the periodic numerical solution.

接着，我们尝试运用数值延拓法求取其周期数值解。

In the numerical computation, a two-dimensional numerical method integrating finite element method and difference method was employed, where the finite element method is used to calculate the magnetic field of the permanent magnetic guideway and the difference method is used to calculate the induced current in the superconductor, then the levitation force and the lateral force were calculated by Lorentz formula.

在数值计算部分，实现了一种集有限元法与差分法为一体的数值计算方法。

A permeance value obtained under one set of test conditions may not indicate the value under a different set of conditions.

在一组试验条件下得到的水蒸气透过系数值不一定能表示试样在其它不同的试验条件下的水蒸气透过系数值。

Such a chaotic attractor was obtained on the phase plane by numerical calculation.

运用数值计算的方法在相平面中得到系统的混沌吸引子，而后对这个混沌吸引子进行数值研究，发现它具有两方面的特征：①它是不连续边界象集的归宿；②具有分数维。

Then thrombectomy was performed with the ATD, HL, OASIS in inferior vana cava. All catheters were used according to the manufactuer's recommendations. Phlebography, pulmonary arteriography were performed, the pulmonary artery pressure and the weight of the clot, the remaining clot in the filter and lungs were measured before and after the procedure.

观测除栓前后肺动脉压力、肺动脉造影、肺动脉内血栓栓塞量及滤器内的血栓残余量、测量注入盐水量和排出液体量计算容量比例、术前动物体内血红蛋白数值和抽吸液体中的血红蛋白数值，计算失血量。

The second experiment is to fabricate white light LED from red and green phosphors pumped by blue light LED. The blue light LED we used in our experiment has the wavelength range between 450 and 452.5 nm, and the chip size is 17 mil *14 mil. There are two kinds white light LED we fabricated in the experiment. There are three blue light LED chips bonded in single package of both kinds package. The different of the both packages is mixed phosphor of encapsulation. One of the experimental devices was encapsulated YAG phosphor mixed silicone to fabricate white light. The other is red and green phosphor mixed encapsulation. The compared and focused parameter was luminous efficiency. YAG phosphor pumped white light has the luminous efficiency 72 lm/W, CRI 70, CIE(0.32, 0.33), CCT 5622°K at the operating current 60mA. On another hand, red and green phosphor pumped white light LED has the luminous efficiency 55 lm/W, CRI 90, CIE(0.31, 0.32), CCT 6479°K at the operating current 60mA. We fabricated the red and green phosphor pumped white light LED, and proved that it could has much higher CRI under similar compared conditions, CIE xy and CCT.

第二个实验是使用蓝光LED晶粒来制作白光元件，蓝光LED晶粒波段范围在450 ~ 452.5 nm，晶粒大小为17*14 mil，以三颗蓝光LED晶粒搭配YAG萤光粉(黄绿光 540 nm)制成白光元件，再以另外三颗蓝光LED晶粒搭配红色萤光粉(613 nm)混合绿色萤光粉(519 nm)制成的白光元件进行发光效率比较；搭配YAG萤光粉的白光元件在注入60 mA的电流时所量测到最大的发光效率是在72 lm/W，演色性数值大约为70，CIE色度座标为(0.32， 0.33)，色温是在5622 °K；而搭配红色萤光粉混合绿色萤光粉的白光元件在注入60 mA的电流时，最大的发光效率在55 lm/W，演色性数值大约为90，CIE色度座标为(0.31， 0.32)，色温在6479 °K；证明了蓝光LED晶粒搭配红色萤光粉混合绿色萤光的白光元件演色性指数可以高达90 以上的结果。

The FEM simulation software of DEFORM was used to simulate the temperature distribution of plug for Diese piercer during cross rolling.

应用DEFORM三维有限元数值模拟软件对狄舍尔穿孔机热轧穿孔过程中的顶头进行了温度场数值模拟，通过模拟和实测分析了顶头开裂、粘钢、塌鼻等失效原因。

On the basis of Movable Cellular Automata,the 2D numerical simulation of tungsten alloy armour piercer piercing armour target is done.

用可移动元胞自动机数值模拟方法，对钨合金(93W)穿甲弹侵彻装甲钢靶板进行二维数值模拟。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新