收敛

In general, stochastic approximation is guaranteed to converge.

在一般的情况下，随机近似方法的收敛效果是受到肯定的。

Simulation results prove that the proposed model is not only effective, but also converged quickly.

仿真结果证明了提出的模型不仅准确有效，而且收敛速度快。

At any point the convergence is the angle between the meridian as represented on the plane and the N grid line.

一点上的收敛角是子午线在平面上的投影与N坐标线之间的角度。

Based on FLAC,a conclusion is obtained that it is not necessary for Lagrange method to solve through motion equation from both the angle of calculation convergence and physical meaning.

通过对FLAC的研究，得出一个结论：拉格朗日方法无论从计算收敛的角度还是从物理意义的角度，基于运动方程求解都是不必要的。

Practical calculation shows that the proposed method can improve the convergence under large power angle conditions and also reduce the computing time by more than 80 percent.

实例计算表明，场路耦合端点量迭代法能改善大功角稳态工况下算法的收敛性，并使计算时间缩短了80%以上。

The secondary mass flux, Z, cavity convergence/divergent angle, and injection angle have different effect on internal performance of DTN.

二次流量、落压比、凹腔扩张角和收敛角、引射角度都对推力矢量状态下的DTN内流性能有着不同的影响。

In order to achieve a tradeoff between vectoring and unvectoring state, the proposed parameters of DTN are: Z=3~4, secondary injection flux is about 3%, cavity divergence angle is about 10°, cavity convergence angle is 20°~30°, injection angle of secondary is about 30° by counterflow injection.

为了实现DTN在推力矢量和非推力矢量下都有较好的内流综合性能，所建议的设计参数为：落压比为3~4，引射量为3%，凹腔扩张角为10°左右，收敛角在20°~30°，引射角度为30°逆流引射角(β=30°)。

To get the steady interface, the ratio of coextrusion flow length to height is at least l-1.5._The role of smooth flow zone is important to reduce the pressure-fall. The higher surface quality of the fluid path can make the velocity field more uniform and the interfacial offset less. However, the layer interface position was almost unaffected by the convergence angle, so for the convenience of die manufacture and extruder\'s collocation, it is fit to make the contact angle as 90°with smooth corner.

在模具结构参数中，共挤出流道的长度和模具壁面光滑程度对界面有重要的影响，根据计算结果得到了方形流道共挤出段长度与高度比的取值范围；而模具入口收敛角对界面的影响不大，在实际生产中为了模具制造和共挤出机布置的方便，可采用圆滑过渡的90°入口角。

In order to ensure the precision and reliability, this paper designs the GPS/Loran C/SINS/AHRS integrated system. In this integrated system, the self-adaptive federated Kalman filter is introduced to revise strap-down inertial navigation system; the heading angle attitude and heading reference system is used to ensure the convergence of heading angle; and the coordination transformation for Loran C is applied to eliminate the constant error of Loran C.

针对导航精度及可靠性，设计了GPS/罗兰C/SINS/AHRS组合导航系统，该组合导航采用了自适应联邦卡尔曼滤波的方法，通过闭环形式校正SINS，并用姿态航向参考系统代替捷联惯性导航系统输出的航向角以保证航向角的收敛，同时对罗兰C的测量值进行坐标变换以消除由于坐标系不同而带来的常值误差。

In view of the tedious and mistakable manual calculation in measuring Gauss projection,coordinate zone transformation and meridian convergence,an itera-tive approximation method is adopted and programmed by BASIC to imple-ment the direct and converse calculation of Gauss projection and computer cal-culation of meridian convergence angle.

针对测量工作中人工进行高斯投影、坐标换带和平面子午线收敛角计算非常麻烦又容易出错的问题，采用迭代法趋近求值，用BASIC语言编制了相应的计算机程序，实现了上述计算。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐