支承

The deign and ma chining of the key components of this shock absorber is introduced, including th e surface treatment of the spline mandrel, the design of disc spring and connect ing housing, and the configuration of sealing and bearing.

介绍了该空气机械减震器关键零部件的设计，包括花键心轴的表面处理技术、联接筒体设计、减震源碟形弹簧组合设计、密封及支承设计。

Raise the rear end of the vehicle using the centre pin on the bottom of the crossbeam high enough so that the ends of the crossbeams are higher than the ears of the anchoring stands.

将车辆的尾端用横梁底部的中心销升到足够高，使横梁的端部高于支承支架的耳部。

In a continuous beam the vertical deflexions at the rigid supports must be zero.

在连续梁中，刚性支承处的垂直变形必须为零。

Calculation results show that general elastics supported continuous beams methods can obtain better precision and can be applied in engineering design.

计算结果表明：采用广义弹性支承连续梁法对矮肋斜T梁桥进行受力性能分析能取得较好的计算精度，并可用于工程设计当中。

The paper summrized lubrication technology and the selection of lubricant for rotary kiln, grate cooler, mill, conveyor mechanical equipment and large scale fan as following,(1)in rotary kiln, apply oil spoon of circulatory lubrication or pump forced oil supply system in the roller supporting mechanism and use (superscript #)680 high load industrial gear oil, and use lubrication method of idle oil wheel or spray in drive gear wheel and select solid lubricant which has high viscosity, strong adsorbability, good abrasion resistance in utmost pressure and lattic crystal structure,(2) in grate cooler, use immersion oil lubrcation in reducer and boiled oil centralized lubrication method in supporting roller and guide roller bearing, choose (superscript #)1 limit pressure lithium lubrcant grease,(3) in mill, use circulatory lubrication with fluxing oil station in drive mechanism and circulatory lubrication with high-low pressure fluxing oil station in main bearing and sliding shoe bearing and select N320 industrial gear oil.

文章全面总结了回转窑、篦冷机、磨机、输送机械及大型风机的润滑技术和润滑剂的选择。其中，(1)回转窑的托轮支承装置一般采用油勺供油的连续循环润滑方式或油泵强制供油系统，润滑油选用680重负荷工业齿轮油；传动大小齿轮的润滑一般采用带油轮或喷雾的润滑方式，润滑剂宜选用粘度高、吸附性强、极压耐磨性好、具有点阵晶体结构的固体润滑剂；(2)篦冷机中传动减速机的润滑一般采用浸油飞溅润滑；托轮，挡轮轴承的润滑一般采用干油集中润滑的方式，润滑脂一般选用锥入度310~340的1极压锂基润滑脂；(3)磨机中传动装置一般采用稀油润滑站循环润滑和冷却的方式；主轴承或滑履轴承的润滑一般采用高低压稀油润滑站循环润滑和冷却的方式，润滑油一般选用N320工业齿轮油。

The result indicated that frequency of fish-shaped cable truss support system would decrease, resulting in increase of temperature.

算例表明，预应力鱼腹式索桁架支承体系固有频率随着温度的升高而减小，具有较强的非线性，其自振频率随着振幅发生变化，其非线性振动呈现&硬弹簧&特性，非线性自振频率高于线性振动频率。

The effects of equivalent torsional stiffness ratio of the flexible support to the main shaft upon system's natural frequency and dynamic torque in different initial conditions are discussed.

揭示了柔性支承刚度系数和主轴扭转刚度系数之比λ等参数对系统固有特性和动态扭矩的影响规律。

Relation of main workshop with different structure, internal force of slab floor and stiffness of bearing beam is discussed by finite element program considering space frame of slab floor, and its result is concluded.

使用考虑楼板作用的空间框架有限元程序，对不同结构型式的主厂房、楼板内力与支承梁刚度的关系进行探讨，并对其结果进行分析总结。

Each of the forcers, which is levitated on the platen as stage moving element by air-bearing, is composed of a permanent magnet and two driving coils to generate X-directional and Y-directional thrust forces against the platen for driving the stage.

线性脉冲马达推动器靠空气支承悬浮在台板上，用以驱动平台。

A mechanical impedence method is described to predict the natural frequences of elastic beam under the condition of dynamic supporting with the example of helicopter tail rptor.

本文以直升飞机尾桨为例，介绍了确定弹性梁在动态支承条件下固有频率的一种机械阻抗方法。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。