摆动的

The different notes of a stringed musical instrument are made by vibrating the strings.

弦乐器的不同音调是使琴弦颤动而产生的。使摆动；以摆动计量

The influence of the instantaneous angle of attack and ST on the performance of propulsion is investigated.

以鱼类尾鳍摆动式推进模式为背景，对二维刚性和柔性水翼摆动运动的非定常水动力性能开展了数值计算，将刚性水翼的计算结果与实验值进行了对比，吻合较好。

Based on the analysis of sway angular velocity and sway angular acceleration of every branch during the movement of movable platform, the effect of additional force and moment of every branch on movable platform are calculated.

分析了动平台运动过程中各个支链的摆动角速度与摆动角加速度，在此基础上考虑了各个支链对动平台的附加力与力矩作用。

Nano-imprint lithography drum paper teeth axis, swayig begnawing workparts paper teeth or wear, allows unleashmy begnawing paper teeth in paper in an inconsistent state in that result in bilateral irregular longitudinal misregister, in which case on slow computers are more likely to occur, because the impact of low-speed machine tipping bucket, the strength of a rotational motion paper teeth ranges of swayig high speed machine is used, and indirect sheet transfer unleashmy simpleplan paper teeth have smaller, at the same time as a result of automatic circulation lubrication oil system, unleashmy and apparatdus paper teeth axis is not easy to wear, but bearing in mind that oil, oilway jam torn oil grinding.

压印滚筒咬纸牙轴，摆动咬纸牙轴或轴套磨损后，不离使得咬纸牙在咬纸功程洋处于不稳不退状况，以至于爆发双边无次序的纵向套印禁绝，这栽环境在不低速机上比辛便当呈现，因为不低速机翻斗撞击辛不小，咬纸牙轴动弹幅度比辛不小，不低速机是拔取摆动不直接递纸，并且咬纸牙闭合幅度也较小，同时又由于有被迫轮回油路编制润滑，所以咬纸牙轴及轴套不便当磨损，但给夺目油眼，油路畅通导致不续油咬不松。

Heavy-duty swing clasps ensure that a swing remains firmly attached to the structure over time.

重型摆动扣，确保摆动仍然坚信，重视结构随着时间的推移。

With a spring installed inside table, you can move it up and down, and it can adjust the pressure, swing it before and after by eccentric wheel and pulley. The swing margin is about 12 degrees. The platform was installed in the L-plate and can correct center to ensure die non-deformation and roundness in polishing process.

工作台里面安装弹簧一根，可以上下移动，并可任意调整压力，利用皮带轮和偏心轮带动，使前后摆动，摆动幅度约12度，而工作台被安装在 L 型拖板上可以任意地对中心，确保在抛光的过程中，使模具不变形及圆度。

The front part is used for adjusting the left and right sides of the drawer door panels, the back part is used for adjusting the up and down of the door panels and the hole in the middle is used for removing the jointers.

首先把前接码插入抽帮里面，侧面有三个调整件，前面一个用于调整抽屉门板左右摆动；后面一个用于调整门板上下摆动，中间的孔位用于拆卸前接码。

Firstly, let us install the jointers in the drawer frame. There are three adjusting parts on the sides. The front part is used for adjusting the left and right sides of the drawer door panels, the back part is used for adjusting the up and down of the door panels and the hole in the middle is used for removing the jointers.

首先把前接码插入抽帮里面，侧面有三个调整件，前面一个用于调整抽屉门板左右摆动；后面一个用于调整门板上下摆动，中间的孔位用于拆卸前接码。

Firstly, let us install the jointers in the drawer frame. There are three adjusting parts on the sides. The front part is used for adjusting the left and right sides of the drawer door panels, the back part is used for adjusting the up and down of the door panels and the hole in the middle is used forremoving the jointers.

首先把前接码插入抽帮里面，侧面有三个调整件，前面一个用于调整抽屉门板左右摆动；后面一个用于调整门板上下摆动，中间的孔位用于拆卸前接码。

Revolving tolerance includes radial and axial runout of assembled bearing inner ring and outer ring, inner ring reference fcace runout with bore and outside cylindrical surface runout with outer reference face.

旋转精度是规定旋转时振摆的，包括内圈及外圈径向摆动和轴向摆动，内圈侧摆及外径面垂直度公差范围。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。