摆动

The M300 is designed to provide a wide range of travel, wire feed, and oscillation parameters to accommodate variances in material type, thickness and joint design.

M300设计了行走速度，送丝速度，摆动频率参数的大范围调整以适应各种焊接材料的类型、厚度和坡口。

Do not stop field swing Young Pioneer then ,the close to driving automobile is yelling

然后，又不停地摆动红领巾，向驶近的汽车大叫着：&停一停！停一停！&

By means of using a disc cutter with a concave end instead of traditional ball-ended or flat-ended ones,and adjusting the cutter axis to move relatively to the component being machined according to some special rules,the envelop formed by the trace of the tool-nose in each pass and the required surface have the same derivatives up to the second order in the plane normal to the feeding direction.

采用二阶密切曲率法，即采用中凹的盘形铣刀取代传统的球头或鼓形铣刀，在每一行程中让刀具轴线相对于工件按特定的规律摆动，使得在垂直于进给方向的法截面中，由刀尖轨迹形成的包络面与理论曲面的法截线具有相同的1阶？

Yun-strip method, the circle-shaped bath temperature higher than the crescent-shaped article transport transport of temperature, the temperature was higher than the crescent-shaped article transport serrated Article transported bath temperature, in the 12mm flat bottom welded seal, using serrated transport of , and with the magnitude and the swinging groove on both sides of the pause, effective control of the bath temperature, so that pore size of the melt is essentially consistent with the roots do not form a welding groove tumor and decrease the chances of burn-through, no penetration has The improvement of the peace panels of the single-sided welding butt welding flat-sided shape is no longer difficult.

运条方法，圆圈形运条熔池温度高于月牙形运条温度，月牙形运条温度又高于锯齿形运条的熔池温度，在12mm平焊封底层，采用锯齿形运条，并且用摆动的幅度和在坡口两侧的停顿，有效的控制了熔池温度，使熔孔大小基本一致，坡口根部未形成焊瘤和烧穿的机率有所下降，未焊透有所改善，使乎板对接平焊的单面焊接双面成形不再是难点。

This puts the swing perpendicular to the wheel and produces the flattest surface.

这使摆动垂直轮和生产平坦的表面。

Result: The knee joint angle of affected-side and unaffected-side of hemiplegic gait showed significant differences on knee flexions at heel-ground (4.49±6.16,14.02±8.49), Max. extension in stand phase (-0.89±3.86, 3.18±5.47), Max. flexion in swing phase (23.11±10.54, 30.28±10.52) and total excursion on sagittal plane (27.94±8.06, 28.94±10.10) comparing with healthy subject.

结果：偏瘫患者患侧和健侧膝关节初始着地时刻(4.49±6.16， 14.02±8.49)、站立相最大伸展角度(-0.89±3.86， 3.18±5.47)、摆动相最大屈曲角度(23.11±10.54， 30.28±10.52)、矢状面膝关节角度范围(27.94±8.06， 28.94±10.10)均与正常人存在显著差异。

One of the best ways to strengthen those hip flexors and in turn improve the power of our swing phase is to do hill repeats.

增 强臀屈肌从而提高摆动力量的一个最好的方法就是山坡间歇跑。

In view of each type of Cam Mechanism, the corresponding programming has been carried on to solve the problem of the visual input of the knife-edge, the roller, the flat-face base translating follower and oscillating follower plate Cam Mechanism.

针对凸轮机构的各种类型，进行了相应的程序编制，解决了尖顶、滚子、平底直动从动件和摆动从动件的盘形凸轮机构可视化输入，实现了自动化设计和参数化绘图。

Results show that structural vibration can be dramatically decreased by changing the angle between the forcing direction of engine shaking and the oscillating direction of engine in structural mode.

实车量测结果与解析说明引擎本体之摆动方向与摇动力之进动方向的相对改变可以戏剧化改变车架的振动环境。

By simulation,the thesis validates that existence of balance-departure-degree in differential force for the grab bucket.

根据抓斗在差动力作用下，抓斗摆动的特点，提出了抓斗消摆控制的解决方案——摆角微分负反馈。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。