搭接的

But to raise the money, Mr Walton, aged 32, has ventured into less ethereal realms of the classical music world: he is cobbling together a syndicate of investors over the next two months who will own notional shares in the instrument.

但是，为了筹到钱，32岁的Walton搅入了和古典音乐完全不搭界的领域：接下来的两个月里，他将为一个辛迪加组织的投资们表演，该组织将名义上拥有这把大提琴。

In addition, the flashing of complex details and creation of an expansion joint at the base of these penetrations to allow for differential settlement can be easily done with the Firestone EPDM Geomembrane system.

另外，复杂节点的泛水处理和在这些穿出件底部的搭接，有了凡士通系统，不同的安装也就很容易完成了。

Under the cases of solution treatments of (1150℃/lh+WQ) and ninefold cyclic heat treatment of 1050℃/30min+AC respectively.

过高的处理温度或过长的处理时间，均会导致第二相的粗化、长大和搭接。

The relationship between softwood longitudinal permeability and its structure was systematically studied based upon the principles of flow.

文首次提出搭接面及侧面胞壁上纹孔在流体纵向渗透时的不同作用，并运用流体力学的原理，对针叶树木材流体纵向渗透性与其构造的关系进行了系统分析。

While under the same anchorage conditions, the ultimate tensile stress in adhesive reinforcement of beam is much smaller than the ultimate stress in pull-out test of block specimen.

将植筋搭接梁的试验结果与块体试件植筋锚固单向拉拔试验的结果比较表明，在相同植筋条件下，梁式试件破坏时钢筋的应力远小于块体试件单向拉拔试件破坏时钢筋的应力。

Secondly, the operating principle and the mathematical model and the control method about the three-level voltage source high power factor PWM converter are analysed .The generation of the PWM trigging pulse control signal are introduced emphatically. On the basis of this, the hardware experimentation circuits are built with DSP and CPLD, and the trigging pulse signal is generated exactly. The feasibility of the circuit is verified by the experiment result.

其次，分析了三相电压型变流器的原理、模型、控制方法并着重研究其PWM 触发脉冲控制信号发生技术，并以DSP、CPLD 等芯片搭接了硬件试验电路，产生了正确地触发脉冲信号，试验结果证明了设计的合理性。

To solve the problem, a three-point bending test was put forward.

中文摘要：针对以Q450NQR1钢为基板、B级钢为腹板模拟实际工装位置，疲劳断裂与货车运营实际工况不符的问题，提出以B级钢为基板、Q450NQR1钢为腹板进行三点弯曲疲劳试验，诱使疲劳裂纹向B级钢侧扩展，研究了MAG气体保护焊B级钢/Q450NQR1钢搭接接头的疲劳性能。

The bond behavior between FRP sheet with FRP shear key and concrete was studied by experiment on a single shear test setup. Test invariables including the height, the width and the length of shear key, appending coarse-sand-coating and concrete compressive strength were considered.

采用FRP板－混凝土块搭接接头的单剪试验方法，考虑剪力键高度、宽度和长度、附加砂粒增强以及混凝土强度等因素，对带剪力键的FRP板与混凝土间粘结性能进行了深入研究。

When the elastic modulus is high, stress and strain are mainly concentrated at edge of the overlap region, while those in weld spot zone are relatively even; when the elastic modulus is low, stresses in the adhesive layer are small while stresses are concentrated to a certain extent at edge of the weld spot.

分析发现，胶粘剂弹性模量对接头中应力应变分布的趋势有明显影响，胶粘剂弹性模量高时，搭接区边缘附近区域应力应变高，焊点区应力应变值相对较小；弹性模量低时，焊点边缘处存在一定的应力集中，胶层中应力较小。

The results show that obvious shearing deformation is found on the lap solder after 4 thermal cycles, then is the visible displacement on the upper and lower surfaces.

结果表明，经过4个温度循环周期后，SnAgCu-CNT 搭接焊点发生了明显的剪切变形，产生了显著的上下表面相对位移。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐