搭接的

Adopt zero velocity full auto paper receiving mode, end to end butt paper receiving, auto double side stickup connection adhesive tape so as to avoid spoilage of die cutter and dinkey dint of overlapping paper registration.

采用零速全自动接纸方式，头对头对接接纸，自动双面粘贴连接胶带，可避免搭接接纸对印版的压伤及对模切刀具的损坏问题。

Based on experimental results of unstiffened overlapped circular hollow section joints, the axial forces of experimental truss members connected with hinge joints, semi hinge joints or rigid joints, are calculated by the finite element analysis model.

以平面K型圆钢管搭接节点的试验数据为基础，通过对试验桁架建立铰接、半铰接和刚接杆系有限元模型，计算受外荷载作用下试验桁架各杆件的轴力。

In this paper, mechanical analysis of over lap section of yieldable steel ribs is made. It describes how to deal with the overlap sections in calculation of internal forces in the support.It analyzes variation of shape of steel ribs and calculation of internal residual forces resulted from yielding of steel ribs. The theory for ca...

本文根据地下结构的特点，着重对可缩性金属支架的搭接段进行力学分析，并提出了在支架内力计算中搭接段的处理方法；分析了支架缩动引起的形状变化及支架由于缩动而产生的残余内力的计算，从而建立了可缩性金属支架的计算理论。

The bearing capacity behavior of 550MPa high strength cold-formed steel lapped continuous hat section battens under bending is studied.

0前言近年来，为提高轻钢结构体系中檩条的承载力，在实际工程中采用一种新颖的通过嵌套搭接实现多跨连续的搭接式连续檩条。

The relationship between the processing parameters and the dilution and the effective utilization of powder coefficient were explained theoretically In the meantime, the theoretical method to analyze the variation of the microstructure and the properties of the cladded layer were formulated.

建立了多道搭接技术条件下熔覆层稀释率、粉末有效利用系数和激光热有效利用率的方程。在搭接过程中，熔覆材料的损失机制主要是烧损。

By analyzing the influence of hemisphere pits with different dimension and ellipsoid pits with different aspect ratio on stress and strain distribution of lap joint, the possible propagation of fatigue crack was discussed, and the effects of localized pitting corrosion on the structural integrity of lap joints were discussed.

通过分析不同尺寸的半球形蚀坑和不同长短半轴比值的半椭球形蚀孔应力应变分布的影响，探讨搭接件疲劳裂纹的可能扩展方向，讨论局部孔蚀对搭接件结构完整性的影响。

To adopt finite meta method analyzes stress strain action of Al-plastic compound pipe under Analog load status and studies the influence of load capacity by variation of diameter of medium Al layer and change of joint part length lap joints.

采用有限元方法分析了铝塑复合管在模拟承载状态下的应力应变行为，研究了中间铝层的直径变化以及搭接接头搭接部分长度的变化对承载行为的影响。

Thermo-mechanical coupling finite element method is used to calculate the six inherent strain components and the angular distortion of the lap joint, and each inherent strain component is mapped into the model in the form of boundary condition for linear elastic analysis, the angular distortions of the lap joint are got.

采用热弹塑性有限元法计算出搭接接头的六个固有应变分量和角变形，并以各个固有应变分量作为边界条件，对搭接接头的有限元模型进行弹性分析，计算出各个固有应变分量对应的角变形。

A detailed calculation results verified the moment and deflection of lapped connection beam is similar as that of continuous beam. So the continuous beam analytic model is suitable for analyzing roof purlins. However, how to guarantee the stability of the bearing compressed zone without the tension bar in bottom flange greatly affect the use of continuous purlins in project, theoretical analysis is carried out.

对搭接模型和均匀连续梁模型的计算结果进行对比，证明采用均匀连续梁的分析模型可较为准确地描述连续搭接檩条的内力状况；而对于仅在檩条上翼缘附近设置拉条，竖向力作用下如何保证支座区受压下翼缘的稳定性在很大程度上影响着连续檩条在工程中的推广应用，因此对其进行了理论分析。

Results show that when improving spot pitch in weld bonded joints with high elastic modulus adhesives, stresses in weld spot zone are decreased while stresses and strains at edges of overlap region are increased slightly. For the joints with low elastic modulus adhesives, both stress concentration degree at the weld spot and the shear strain at edges of overlap region are increased with the spot pitch increasing.

结果表明，高弹性模量胶粘剂胶焊接头中，增大焊点间距，焊点区应力减小而搭接区边缘胶层中的应力应变略有增大；低弹性模量胶粘剂胶焊接头中，焊点处应力集中程度和搭接区边缘胶层中的剪应变值都随焊点间距的增加而增大，增加焊点间距，两种接头的胶层断裂强度都将降低。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐