英语人>网络例句>搭接 相关的搜索结果
网络例句

搭接

与 搭接 相关的网络例句 [注:此内容来源于网络,仅供参考]

Adopt zero velocity full auto paper receiving mode, end to end butt paper receiving, auto double side stickup connection adhesive tape so as to avoid spoilage of die cutter and dinkey dint of overlapping paper registration.

采用零速全自动接纸方式,头对头对接接纸,自动双面粘贴连接胶带,可避免搭接接纸对印版的压伤及对模切刀具的损坏问题。

In this research we discovers that mortise and tenon joint, dovetail joint, tongue joint, finger joint, and dowelled joint are very interesting and functional joint methods.

本研究发现传统的木式结构的对接、搭接、榫接和拼接等的技法是非常有趣和极具功能性的接合方式。

Due to the large area of one single tile, fewer roof joints and scientific design of specific fastener.

瓦单张面积大,屋面接缝很少,且搭接处结合严密,因此拥有卓越的自防水性能,可省去防水层,从而降低建筑物造价。

Based on experimental results of unstiffened overlapped circular hollow section joints, the axial forces of experimental truss members connected with hinge joints, semi hinge joints or rigid joints, are calculated by the finite element analysis model.

以平面K型圆钢管搭接节点的试验数据为基础,通过对试验桁架建立铰接、半铰接和刚接杆系有限元模型,计算受外荷载作用下试验桁架各杆件的轴力。

First of all, the concept of S-N curve and the procedures of p-S-N curve fatigue test, data processing were introduced. And then, these procedures were taken into practice on 4 kinds of aluminum alloy welded joints: corner joint, butt joint, cruciform joints and double-sided lap joint.

文中首先介绍了S-N曲线的概念和p-S-N曲线疲劳试验方法和数据处理方法,并按照这些方法对角接、对接、十字接和双面搭接四种铝合金焊接接头试样进行了疲劳试验,得出了这四种焊接接头的中值S-N曲线和置信度为95%,存活率分别为90%、99%下的p-S-N曲线及其方程。

The effect of environment corrosion and salt fog on fatigue properties of 3 types of bolted joint structures and 12 kinds of protective measures of LY12CZ Al- alloy plate typical bolted lap joints was studied by an accelerated corrosion test.

采用加速腐蚀试验方法,研究了环境腐蚀和盐雾对LY12CZ铝合金板材的3种螺接型式、12种防护处理的典型螺接搭接件疲劳性能的影响,提出了几种较适用的螺接结构细节防护方法。

A detailed calculation results verified the moment and deflection of lapped connection beam is similar as that of continuous beam. So the continuous beam analytic model is suitable for analyzing roof purlins. However, how to guarantee the stability of the bearing compressed zone without the tension bar in bottom flange greatly affect the use of continuous purlins in project, theoretical analysis is carried out.

搭接模型和均匀连续梁模型的计算结果进行对比,证明采用均匀连续梁的分析模型可较为准确地描述连续搭接檩条的内力状况;而对于仅在檩条上翼缘附近设置拉条,竖向力作用下如何保证支座区受压下翼缘的稳定性在很大程度上影响着连续檩条在工程中的推广应用,因此对其进行了理论分析。

Results show that when improving spot pitch in weld bonded joints with high elastic modulus adhesives, stresses in weld spot zone are decreased while stresses and strains at edges of overlap region are increased slightly. For the joints with low elastic modulus adhesives, both stress concentration degree at the weld spot and the shear strain at edges of overlap region are increased with the spot pitch increasing.

结果表明,高弹性模量胶粘剂胶焊接头中,增大焊点间距,焊点区应力减小而搭接区边缘胶层中的应力应变略有增大;低弹性模量胶粘剂胶焊接头中,焊点处应力集中程度和搭接区边缘胶层中的剪应变值都随焊点间距的增加而增大,增加焊点间距,两种接头的胶层断裂强度都将降低。

Under any circumstance, lap length of longitudinal carrying bar binding lap shall not be less than 300mm.

注:(1)在任何情况下,纵向受拉钢筋绑扎搭接接头的搭接长度均不应小于300mm。

This article introduces joint type of copper-aluminum pipe,including straight pipe butted joint,flared pipe insert joint,reducing pipe insert joint and reducing pipe lap joint,and the welding technologies in domestic and abroad,including friction welding,energy storage welding,flash welding,resistance welding,braze welding,cold butt welding and ultrasonic welding.

介绍了铜铝管的接头形式,主要包括:直管对接、扩口管插接、缩口管插接和缩口管搭接;以及国内外的焊接技术,主要包括:摩擦焊、储能焊、闪光焊、电阻焊、钎焊、冷压焊及超声波钎焊等。

第3/12页 首页 < 1 2 3 4 5 6 7 8 9 ... > 尾页
推荐网络例句

With Death guitarist Schuldiner adopting vocal duties, the band made a major impact on the scene.

随着死亡的吉他手Schuldiner接受主唱的职务,乐队在现实中树立了重要的影响。

But he could still end up breakfasting on Swiss-government issue muesli because all six are accused of nicking around 45 million pounds they should have paid to FIFA.

不过他最后仍有可能沦为瑞士政府&议事餐桌&上的一道早餐,因为这所有六个人都被指控把本应支付给国际足联的大约4500万英镑骗了个精光。

Closes the eye, the deep breathing, all no longer are the dreams as if......

关闭眼睛,深呼吸,一切不再是梦想,犹如。。。。。。