插补

The results show that the algorithm makes all of the interpolating points in the theoretical curve and assures the high speed and precision requirements of the motion control system.

结果表明，该算法能使所有的插补点都在理论曲线上，可以保证运动控制系统的高速高精度要求。

To solve problems of the wheel interference and the linear speed change on grinding points which has an effeet on the grinding surface roughness,a polar-coordinate-based equal step interpolating method for the grinding point trace is presented.

为解决砂轮干涉及磨削点处线速度变化影响磨削表面粗糙度的问题，提出了极坐标下砂轮磨削点轨迹的等步长插补方法，该方法可应用于任何具有C1连续性的正则曲线的CNC磨削。

Trilinear bilinear interpolation to deal with than dealing with the calculation of the need for greater capacity, and the need for greater bandwidth of the memory clock.

三线性插补处理比双线性处理需要更大的计算量，而且需要更大的存储器时钟带宽。

At second, the system make use of the values to calculate the equations about actual trochoid and academic trochoid of cutter moving and deduce whether the hardware interpolation component executing normally or not.

再计算并判断刀具实际与理论运动轨迹的等式成立与否，由此判断硬件插补器工作是否正常。

First,wavelet transform decomposes the original image,then the coefficients of the three directions are used to construct the band-cross vector,and then the vectors are classified.In addition,new vector quantization technologies are used in this algorithm.

该算法在对图像进行多级小波变换后，构造三个方向的跨频带矢量，同时采用分类矢量量化，非线性插补矢量量化和基于人眼视觉特性的加权矢量量化，提高了图像的编码效率和重构质量。

You can obtain the desired vector component. Reconstruction gradients are typicallyused when you want to implement your own interpolation scheme. Reconstruction gra

参数0代表X方向的分量，1代表Y方向的分量，2代表Z方向的分量）当你完成你自己的插补计划时可以使用改造过的梯度。

Then,have an in-depth study on S-shaped curve,and find out the acceleration,vel...

最后给出了程序段预处理过程流程图和程序段插补过程流程图。

According to this result, an optimal procedure can be employed to determine these parameters in the kinematic design of PKM, which enable the desired ratio of workspace volume, well-conditioned dexterity, and desired velocity capability to be simultaneously achieved without occurrence of strut interference.

本文以基于6-TPS Stewart平台的并联机床为研究对象，研究了该类机床数控系统中有关运动控制的一些关键问题，并针对在运动控制中引发的微分运动分析与综合、解轨迹上的非线性特性及其引起的插补原理性误差等并联机床的运动学性能问题进行了研究。

The direct weight address mapping techniques are used in this model and algorithm, and the relation between the inputs and the weights is established by taking the inputs of training samples as their weight address, and the corresponding weights are found for any inputs by taking it as similar weight address, and the accurate outputs are obtained by the associable insertion algorithm.

模型、算法采用直接权地址映射技术，以训练样本的输入为地址，建立起输入与权重的关系。任意输入作为相近的权地址，即可找到对应的权，经过联想插补后可获得高精度输出。

This algorithm constructs a 64-D crossband vector according to the characteristics of the decomposed image, and adopts nonlinear interpolative vector quantization and soft computing based codebook generation algorithm. Hence, this algorithm can improve the vector quantization performance significantly from both aspects of speed and precision, and it can get a high reconstruction quality (PSNR＞34dB) with a very low bit rate (0.172bpp).

该方案依据图象小波变换的特点构造了64维的跨频带矢量，并采用了非线性插补矢量量化和柔性计算码书生成算法，从速度和精度两方面提高矢量量化的性能，从而在极低比特率的条件下(0.172bpp)获得了高质量的重构图象(PSNR＞34dB)。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。