插值函数

In Chapter Three, we use the method of interpolation spline of differential operater to come up with the reproducing kernel in H01 with respect to bounded linear operator in H10. Then we use the reproducing kernel to develop the expression of the best approximating of bounded linear operator in H10 and prove its convergence.

第三章中，对于H_0~1中的有界线性算子，用微分算子插值样条函数的方法给出了H_0~1空间中的再生核，利用此再生核给出了H_0~1上的有界线性算子的最佳逼近的表达形式，并证明了其收敛性。

The finite element numerical method based on centimo theory and dispart-insert-value One side ,it is conventional energy method. It is transfiguration of Ritz-Galerkin method .

在求解非线性波动方程时，有限元方法通过剖分插值构造有限维子空间SN的基函数的方法保持了古典Ritz-Galerkin方法的优点，克服了它的不足。

Fibrations of congruence of lines and applications of sections ;2. The few group section is calculated for several in core assemblies,and the parameter section table is ordered by different Gd 2O 3 weight percent, burnup, energy group, and then the necessary sections for in core burnup are calculated with function .

本文介绍的组件均匀化参数计算的处理方法是以先进的燃料组件软件包TPFAP为基本工具，对于堆内各种类型组件计算少群截面，按Gd2O3不同重量百分比、比燃耗、能群等顺序组成参数截面表，再用函数插值法求得全堆燃耗计算所需的截面。

Our approach consists of the following steps: providing a sketch based mapping between the sources and the target; deforming the target based on the deformations of the corresponding sources by means of differential mean value coordinates; smoothing the deformed target with constrained minimization method to form a key frame of the target animation; and interpolating between key frames created from to produce a complete 3D animation of the target.

该框架由以下几个步骤组成：使用草图在源网格和目标网格间建立映射；使用非闭合网格均值坐标，根据源动画的运动风格来变形目标网格；对变形后的目标网格求解最小化约束函数以获取光滑的目标网格，从而生成目标动画的关键帧；对由产生的结果进行插值，产生完整的目标对象的三维动画。

We mainly use the barrier functions, the interpolation inequality, a prior estimate and continuity method in this thesis.

本文所用的主要方法，包括构造闸函数，插值不等式，先验估计以及连续性方法。

This is for my use of cubic spline function interpolation method procedures.

详细说明：这是我编的利用三次样条法进行函数插值的程序。

In view of the problems in the traditional highway vertical curve design,the cubic interpolation spline function replacing the conventional curve is proposed and the formula of function is demonstrated.

针对传统的公路竖曲线设计中存在的一些问题，可提出使用三次插值样条函数来替代传统线形的思路。

In this paper, therefore, a new interpolation method using cubic spline function is presented for range migration correction. Using the method we presented, SAR imaging simulation of point target has been done and the experiment results are satisfactory.

作者用三次样条函数插值进行距离徙动校正，进行了点目标SAR仿真成像，得到了满意的仿真结果。

Interpolative control; Cubic spline function; Simulation; Error

插值控制；三次样条函数；仿真；稳态误差

The results show that the response of control is quick, and no over-control, the error can be negligible, and the design is simple. The interpolative control based on cubic spline interpolation function also can be used for sparse rules base, which has few knowledge of expert.

仿真结果表明，基于三次样条函数的插值控制，具有响应快，无超调，稳态误差极小等优点，并且设计简单，不需要过多专家经验就可以完成很好的控制，适用于稀疏规则库条件下的控制。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。