提高

Compared with that of 3Cr13 alloy, the oxidation resistance of the composites containing 5 vol.％TiC particle was improved greatly at 850℃, but the improvement was relatively limited at 950℃. But the oxidation resistance of 1Cr18Ni9 composites containing 5 vol.％ TiC particle was obviously improved at 950℃, and at 850℃ the improvement is not large. The TiC particle can improve the oxidation resistance mainly was by developing the oxidation selectiveness of the Cr element as to change the phase constitution of the oxidation film, to alleviate the production of the stress in the oxidation film and to improve the cohesive force of the oxidation film or matrix interface and the chemical combination of the oxidation film.

与3Cr13合金相比，含5％volTiC颗粒的复合材料在850℃的抗氧化性能得到大幅度提高，而在950℃复合材料的抗氧化性能提高作用却是有限的；与1Cr18Ni9合金相比，含5％volTiC颗粒的复合材料在850℃的抗氧化性能略有提高，而950℃复合材料的抗氧化性能提高却是明显的；TiC颗粒可以提高两种基体合金抗氧化性能，主要是通过促进Cr的选择性氧化，进而改变氧化膜的相组成、减缓氧化膜内应力的产生、增加氧化膜/基体界面凝聚力及提高氧化膜化学结合力而实现的。

The experiment two: enzyme preparation significantly improved average daily gainand feed conversion ratio (P＜0.05). Enzyme preparation significantly increased energymetabolizability and digestibility of crude fiber, crude protein and neutral detergent fiber,but had no remarkable effect on digestibility of dry matter, crude fat and acid detergentfiber. Enzyme preparation significantly decreased the relative viscosity of duodenal andjejunal digesta. The pH of intestine had no noticed difference in all groups. Enzymepreparation significantly decreased relative weight of gizzard, proventficulus, duodenum,jejunum and ileum. Enzyme preparation significantly increased villus size of duodenumand jejunum, and villus to crypt ratio of duodenum and ileum significantly increased too.Enzyme preparation considerably decreased ileal crypt height (P＜0.05), and didn"t affectthickness of intestinal wall. Supplementing enzyme preparation, the serum glucose, totalprotein and alanine aminotransferase, but enzyme preparation hadn"t noticed influenceupon uric acid, total cholesterol, triglyceride and high-density lipoproteins. Enzymepreparation significantly increased insulin, triiodothyronine and insulin-like growthfactor-Ⅰ. Adding enzyme preparation, the percentage of thyroid stimulating hormone andgrowth hormone in the serum increased 16.44%, 19.18% and 18.84%, 21.74%respectively, and the percentage of glucagon and thyroxine decreased 12.07%, 14.36% and 13.79%, 15.40%, but failed to reach statistical significance (P＞0.05). Enzymepreparation significantly increased (P＜0.05) the trypsin and amylase activity of duodenaland jejunal digesta, but enzyme preparation didnt affect significantly (P＞0.05) theintestinal lipase activity and pancreatic digestive enzyme. Enzyme preparation had nosignificant effect on caecal microbial population.

试验二：酶制剂显著提高平均日增重和饲料转化率(P＜0.05)；酶制剂显著提高能量代谢率及粗纤维、粗蛋白、中性洗涤纤维消化率(P＜0.05)，而对干物质、粗脂肪、酸性洗涤纤维消化率影响不显著；酶制剂显著降低十二指肠和空肠食糜相对粘度(P＜0.05)；添加酶制剂对肠道pH影响不显著；酶制剂显著降低肌胃、腺胃、十二指肠、空肠、回肠相对重(P＜0.05)，显著提高十二指肠和空肠绒毛高度，显著增加十二指肠和回肠绒毛高度／隐窝深度，降低回肠隐窝深度(P＜0.05)，对肠壁厚度影响不显著；酶制剂显著提高血清葡萄糖、总蛋白和谷丙转氨酶浓度(P＜0.05)，对尿酸、总胆固醇、甘油三酯及高密度脂蛋白浓度影响不显著，显著提高胰岛素、T_3、IGF-Ⅰ水平，添加酶制剂后，促甲状腺激素、生长激素分别提高16.44％、19.18％和18.84％、21.74％，胰高血糖素和T_4分别降低12.07％、14.36％和13.79％、15.40％，但差异不显著；酶制剂对胰腺消化酶活性影响不显著，显著增加十二指肠和空肠胰蛋白酶、淀粉酶活性，对小肠脂肪酶活性影响不显著；酶制剂对盲肠微生物菌落数影响不显著。

Result of thermogravity analysis showed that the thermal stability of polyvinylamine chloride lowers with increasing in amination degree. Moreover, properties of dilute aqueous solutions of three types of poly chloride with different amination degree were compared by use of viscosimetric, conductometric, and potentiometric measurements. Results showed that both the electrostatic interaction of neighboring groups on the chain and the reduced viscosity of poly chloride are increased with increasing the degree of amination of poly . The equivalent conductivity is decreased with the increasing the concentration of poly chloride and increased with the increasing the amination degree of poly .

研究了聚乙烯胺盐酸盐的热稳定性和水溶液性质，发现：随着胺化度的提高，聚乙烯胺盐酸盐的对热稳定性逐步降低；聚乙烯胺盐酸盐是一种典型的聚电解质，其水溶液的pH值随平均分子量的变化并不明显，而随着聚乙烯胺胺化度的升高，pH值降低；随着聚乙烯胺盐酸盐的平均聚合度由82.3增加到201.8，它的m值（用于表征聚电解质侧链基团之间相互作用大小的常数）从5.13升高到5.58，而当聚乙烯胺盐酸盐的平均聚合度增加到311.4时，它的m值反而降低到了5.48；随着胺化度由55.65%升高到82.36%，m值由3.65提高到5.50；随着聚乙烯胺盐酸盐的平均聚合度的提高，聚乙烯胺盐酸盐的平均解离常数由7.48降低到7.26，同时随着胺化度的提高，聚乙烯胺盐酸盐的平均解离常数也由8.33降低到7.37；随着聚乙烯胺盐酸盐浓度的提高，溶液的摩尔电导率逐步降低，随着聚乙烯胺胺化度和聚合度的提高，溶液的摩尔电导率有所升高；在pH值为4左右时，聚乙烯胺盐酸盐的比浓粘度分别达到极值，而与聚合度的大小关系不大；聚乙烯胺盐酸盐的特性粘数明显高于其原料聚丙烯酰胺的特性粘数，分子量对特性粘数的影响十分明显，胺化度对特性粘数的影响并不显著。

Compared with control,①the mean tumor weight of H22 of SXKA Granules three dose groups were decreased significantly(P.01,P.05),and the mean inhibition rates of SXKA Granules 20、10 g/kg dose groups were above 30%;②the mean tumor weight of S180 of SXKA Granules three dose groups were decreased significantly(P.01),and the mean inhibition rates of SXKA Granules 20、10 g/kg dose groups were above 32%;③the mean tumor weight of EAC of SXKA Granules three dose groups were decreased significantly ( P.01, P.05),and the mean inhibition rates of SXKA Granules 20 g/kg dose groups were above 38%;④the mean tumor weight of Lewis carcinoma of SXKA Granules three dose groups were decreased significantly(P.01, P.05),and the mean inhibition rates of SXKA Granules 20、10、5 g/kg dose groups were above 36%;⑤the mean tumor weight of W256 of SXKA Granules three dose groups were decreased significantly ( P.01, P.05),and the mean inhibition rates of SXKA Granules 20、10 g/kg dose groups were above 32%;⑵Compared with control,SXKA Granules 20、10 g/kg dose groups had extended the survial time of the P388-bearing mice respectively(P.01),and the mean prolong rates of SXKA Granules 20、10 g/kg dose groups were above 50%;⑶Compared with S180-bearing group, SXKA Granules 20、10 g/kg dose groups could increase the weight of thymus and spleen, Spleen index and thymus index were increased, SXKA Granules 5 g/kg dose group could increase thymus index(P.05);⑷As Compared with control group, SXKA Granules 20、10 g/kg dose groups could improve mouse serum half hemolysis value depressed by transplanted tumor dramatically(P.01), which revealed the SXKA granules could improve the mouse humoral immunity system;⑸SXKA Granules 20 g/kg dose group could increase of englobe indexαon S180-bearing mice remarkably(P.01), which indicated the SXKA Granules could improve their cellular immunity system.

对荷W256大鼠，生兴克癌冲剂20、10、5 g / kg三组的平均瘤重明显低于对照组(P.01，P.05)，生兴克癌冲剂20、10 g / kg组的平均肿瘤抑制率均大于32 %；⑵与空白对照组相比，生兴克癌冲剂20、10 g/ kg能显著地延长移植小鼠白血病P388小鼠的存活天数(P.01)，生兴克癌冲剂20、10 g/ kg对荷白血病P388小鼠生命延长率均在50%以上；⑶与S180荷瘤组相比，生兴克癌冲剂对荷瘤鼠的免疫器官重量、胸腺指数和脾指数有一定的提高趋势，其中生兴克癌冲剂5 g / kg组对荷瘤小鼠的胸腺指数有一定的提高作用(P.05)；⑷与S180荷瘤组相比，生兴克癌冲剂20、10 g /kg组可提高由荷瘤引起的小鼠血清半数溶血素值的降低(P.01)，表明其可提高荷瘤小鼠体液免疫功能；⑸与对照组相比，生兴克癌冲剂20 g /kg组可提高荷S180肉瘤小鼠的免疫吞噬系数α值(P.01)，表明其可提高荷瘤小鼠细胞免疫功能。

The results show that when the cathode humidified temperature increase, the humidification of membrane and fuel cell performance improved at lower current density, while the saturation in diffusion layer increase and the performance decreases at higher current density. Humidification of membrane and fuel cell performance improved when the anode humidified temperature increase, the saturation in diffusion layer decrease and fuel cell performance improved when the fuel cell working temperature increase, the resistance of diffusion layer decrease and the performance improved when the porosity largen. At last, the simulation results are compared with the experimental results and they are basically the same.

结果表明随阴极加湿温度的提高，在低电流密度运行时膜的润湿条件改善，燃料电池性能提高，在高电流密度运行时扩散层中液态饱和度增加，燃料电池性能下降；随阳极加湿温度的提高，膜的润湿条件改善，燃料电池性能提高；随燃料电池运行温度的提高，扩散层中液态饱和度下降，燃料电池性能提高；随气体扩散层孔隙率增加，气体扩散层阻力减小，燃料电池性能提高。

Study result suggest: The change of stock in RFCCU directly affect gasoline content. Gasoline content can be reduced through increasing the equilibrium activity of catalyst, controlling reaction level, increasing recirculating rate of gasoline and stability of gasoline level. Conclusions drawn from experiment is that optimization of operating condition has great effect on lowering olefine content of gasoline which can be reduced from 60% to 50%.Reducing reaction temperature is useful for lowering olefine content of gasoline, when the reaction temperature is raised, thermal cracking rate is higher than catalytic cracking rate, so that olefine content is increased. Raising catalyst-to-oil ratio is good for lowering olefine content. With conversion rate increased, the yield of LPG and coke is raised, the yield of gasoline is increased firstly and then decreased slightly, hydrogen transfer index is increased, so the olefine content is decreased.

研究结果表明：催化裂化装置的原料的变化直接影响到催化汽油的烯烃含量；可以通过优化催化装置的操作条件来降低催化汽油中的烯烃含量，其中通过提高催化剂平衡活性、控制反应深度、增加汽油回炼量、汽油深度稳定可以降低催化汽油烯烃含量，优化工艺条件对降低催化汽油烯烃含量有较大作用，汽油烯烃含量由60％降至50％左右；降低反应温度有利于降低催化汽油的烯烃含量，当反应温度的提高，热裂化反应速度提高的幅度大于催化裂化反应速度提高的幅度，汽油烯烃含量增加；剂油比的提高有利于降低催化汽油的烯烃含量，转化率提高，液化气产率提高，汽油收率先增加后略有下降，焦炭产率增加，氢转移反应指数提高，汽油烯烃含量下降；反应时间对产品分布及汽油烯烃含量有影响，增加提升管反应时间，液化汽、汽油产率提高，干气和焦炭产率增加。

These tests show that: 1. suction decreases with the increase of the water saturation in the chalk; 2. stress variants proposed are available for describing the stress state of the unsaturated chalk; 3. preconsolidation pressure increases with suction, while the effects of suction on the compressibility coefficients λ and κ are not evident; 4. as usual unsaturated soils, the permeability to oil of chalk increases with the suction; 5. yield strength of the chalk behaves with volumetric strain hardening; 6. cohesive behaviour of the chalk is related to the stress level, and relation between time-dependent deformation and logt is linear; 7. cohesion of the chalk decreases with the increase of the suction, while the elastic stiffness and the cohesion coefficient increase; 8. strength and elastic modulus increase with the strain rate, while the strain at the peak strength decreases with the increase of the strain rate.

试验结果表明，白垩中的虹吸力随水饱和度的降低而提高；吸力、水饱和度和强度的变化过程均与时间有关；可用由理论分析得到的应力状态变量描述非饱和白垩的平衡状态；前期固结压力随吸力增加而提高，而压缩指数λ与κ则同吸力无关；应力大于前期固结压力时，粘性变形与时间的对数关系曲线呈线性关系，其大小和增长速率均随吸力减小而增大，可视为白垩弹性刚度降低和粘性系数增大的结果；前期固结压力和变形模量随着应变速率的提高而提高，压缩指数κ和λ则随应变速率的提高而减小；应变速率较低时，粘性和吸力对前期固结压力及压缩指数的影响较小；白垩中油的渗透性随着吸力增加而提高；白垩在屈服阶段具有明显的体积应变硬化特性。

During the non-isothermal crystallization, compared with common PE, the cooling rate had less impact on the crystallization rate of mPE. Second, the sensitivity of the melt viscosity of mPE to the shear rate was poor, and the introduction of long chain branches onto the molecular structure of mPE could improve the dependence of their melt viscosity on both shear rate and temperature. In the extensional rheometric tests, the occurrence of phenomena of'strain hardening' relied on the structure of linear long chains, and mPE didn't show the behavior of'strain hardening', which implied that the melt strength ofmPE was poor.

其中通过共聚方法在mPE分子中引入非线性长支链结构，对提高mPE熔体粘度对温度的依赖性作用较为明显，而对提高mPE熔体粘度对剪切速率的依赖性以及对提高mPE熔体强度作用较弱；采用共混方法在mPE体系中引入线性长支链结构，则对提高mPE熔体粘度对剪切速率的依赖性以及提高mPE的熔体强度的作用较为明显，而对于提高mPE熔体粘度对温度的依赖性作用相对较弱。

The results show that:First, concentration of hydrogen peroxide have the most obvious influence to oil yield and carbon black yield,with the increase of concentration of hydrogen peroxide the oil yield first increase then decrease,when concentration of hydrogen peroxide is 8.19% or so,the oil yield reach to the biggest value, and with the increase of concentration of hydrogen peroxide carbon black yield decrese;Then,reaction time have more obvious influence to oil yield and carbon black yield,oil yield increase but carbon black yield decrease with the increase of reaction time;Thirdly,reaction tempreture have some influence to oil yield and carbon black yield,samely,oil yield increase but carbon black yield decrease with the increase of reaction tempreture;Finally,reaction pressure does almost no influence on oil yield and carbon black yield.

研究结果表明：过氧化氢质量浓度对产油率和炭黑产率的影响最为显著，产油率随过氧化氢质量浓度的提高先提高后降低，在过氧化氢质量浓度为8.19%左右时达到最大值，炭黑产率随过氧化氢质量浓度的提高而降低；反应时间对产油率和炭黑产率的影响也比较显著，产油率随反应时间的增加而提高，炭黑产率随反应时间的增加而降低；反应温度对产油率和炭黑产率也有一定的影响，产油率随反应温度的提高而相应地提高，炭黑产率随反应温度的提高而降低；在本文实验范围内，反应压力对产油率和炭黑产率基本上没有影响。

The following main results are obtained: The TiO_2 photocatalyst with small crystallite size, high surface area, narrow and uniform pore size distribution, and microporous frameworks could be prepared out by applying MW radiation in the preparation process. The microwave-induced fluorescence technique verified for the first time that microwave enhanced the formation rate of hydroxyl radical, leading to the increase in the photocatalytic efficiency. Compared with the conventional catalyst, TiO_2 prepared by MW dielectric heating owns a higher UV absorption ability, and its optical absorption edge and photovoltaic response are shifted toward the short wavelength region, resulting in increase of photooxidation efficiency. The photocatalytic conversion and the mineralization ratio of acetaldehyde are increased respectively by 30% and 40% over the TiO2 prepared by MW radiation when compared to the TiO2 prepared by the conventional heating. For the MW-assisted photocatalytic reaction over the MW-prepared TiO2, production of hydroxyl radicals is enhanced by 22.5%, and the photocatalytic conversion is accordingly increased by 20%. Similarlly, applying MW also increased the photocatalytic conversion and the mineralization ratio of acetaldehyde over TiO2/Al2O3 sample.

论文得到如下主要结果和结论：(1)微波介电加热TiO_2 溶胶可得到晶粒度小、光催化活性高、比表面积大和孔径分布窄而均一，且微孔发达的TiO_2光催化剂；在溶胶干燥处理过程中微波可使催化剂表面缺陷增加，进而导致光催化反应过程有更多的活性羟基自由基产生；(2)微波制备能显著增强TiO_2 样品的紫外光吸收率，并使其光吸收和光伏响应阈值发生蓝移，从而提高TiO_2的氧化还原能力；(3)与常规加热法所制TiO_2比较，微波法制备的TiO_2对乙醛的光催化降解转化率提高30%，CO_2生成率提高40%以上；(4)与未加微波辐射时相比，发现在光催化反应过程中施加微波，TiO_2 的羟基自由基生成速率提高了22.5%，相应CH_3CHO 光催化降解转化率提高了20%；对Al_2O_3/TiO_2催化剂，CH_3CHO 光催化降解转化率甚至提高了33%，同时CO_2 的生成率也都大幅度提高；(5)微波辐射可改变光催化降解乙醛的产物分布，推断施加微波时乙醛光催化降解按照羟基自由基引发的链式反应机理进行，微波&非热效应&起主要作用。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。