控制的

On the basic of completed the wave control, we studied the accelerated arithmetic. The speed of measurement has widely improved by using the accelerated arithmetic.

我们在完成了对激磁电压控制的基础上并研究了波形控制的加速算法，从而使磁化特性的测量速度有了很大提高。

A method on the temperature precision control of Thermo-fixing machine by conjunction of main controller with assistor are given out.

设计了一种基于S3C44B0X的嵌入式温度监控系统，介绍了该系统的组成和工作原理，提出了采用主辅控制相结合，对热定型机烘房温度精确控制的方法。

This system has function dispersion and can deal withparameter checking, calculation, control strategy, information output andprocess parameters time-control. These functions will auto-run effectuallyand reliably that make control dispersion.

在此理论基础上，论文提出了一种应用于印刷业张力联动控制的基于现场总线技术的集散控制系统DCS2000-MRT，介绍了该系统的主要功能、硬件组成、工作原理、软件设计及其实现方法。

In addition, the primary causation for the problem that phase current during reverse braking process out of control is a short loop by the back electromotive force.

同时，针对反接制动时电流无法控制的问题，该文指出反电动势短接回路的存在是造成再生电流无法控制的主要原因。

On the basis of the concept of space vector, the basic theory of DTC is analyzed. Also a representative DTC strategy improving operation performance of induction motors, which is called DSVM, is introduced.

在阐述空间矢量概念的基础上，分析了传统两电平逆变器异步电机直接转矩控制的基本原理，并引入了一种典型的直接转矩控制改进算法DSVM。

This book gives a brief account of significance and historical development of quality control, emphasizes various types of control charts and acceptance sampling systems and procedures, and gives a brief and direct introduction of probability and statistics.

本书简要概述了质量控制的意义和历史发展过程，重点讲解了各种类型的控制图和抽样检验体系和过程，而对概率和统计知识的介绍非常直观和简单。

The task of course control is completed by realization and the design of control system.

过程控制的任务是由控制系统的设计和实现来完成的。

So this paper develops several schemes of cathode design and their merits and demerits are analyzed and compared.

针对齿轮修形的特点，本文设计了基于单片机控制的脉冲电化学齿轮修形控制系统，实现了加工过程的自动化。

By using the computing method of this paper, emendation error after yaw-steering can be reduced to centesimal Hz level. Thus, precise computation of yaw-steering is successfully achieved.

利用该文提出的计算方法，采用偏航控制的多普勒中心校正误差可以达到0.01Hz量级，从而实现了偏航控制的精确计算。

Combined with practice,Variable tension control idea of special steel coiler for hot strip mill is introduced.

热连轧卷取机的张力控制是带钢卷取控制的核心，如何提高带钢卷形合格率一直是热连轧工序研究的课题。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。