控制信号

The system consists of signal acquisition systems, signal processing, show circuit and control circuits, and other components, through the acquisition by Hall sensor voltage signal to the amplifier will signal amplification, and then in the A / D converter after the digital signal into the microcontroller , Through the SCM software programming by the magnetic field signal, the final adoption of LED display to the magnetic field strength.

该系统由信号采集系统、信号处理、显示电路和控制电路等组成，通过霍尔传感器采集得到电压信号，再经放大器将信号放大，然后在A/D转换后将数字信号送入单片机，通过单片机软件编程得到磁场信号，最后通过LED显示出磁场强度。

It shows that the control pulse width, the SOA length effect and the nonlinear gain compression effect influence the width of the switching window, and they are the main factors in limiting the switching speed of the CPMZ configuration.

研究表明：控制脉冲宽度、半导体光放大器的长度和非线性增益压缩影响着控制脉冲和信号脉冲反向传播开关窗口的大小，是限制控制脉冲和信号脉冲反向传播高速工作的主要因素。

The key technologies of ABS based on slip-ratio consist of processing of wheel speed and calculation of wheel acceleration, estimation of vehicle velocity, estimation of the optimal slip-ratio, and the control strategy of ABS. In order to improve the performance of conventional ABS, the above mentioned key technologies and corresponding realization algorithms had been investigated in this paper, and the ABS product equipped in vehicle for performance test had been manufactured.

结合车辆动力学控制的最佳ABS系统是以车轮滑移率为控制目标的ABS系统，它涉及到一系列关键技术研究，如轮速信号的处理方法和轮加速度信号的计算方法、车身速度估计方法、最佳滑移率估计方法和ABS的控制方法等。

A control device (14) includes means for outputting a request signal to an electornic key (12) in response to the ON operation of a predetermined switch start switch (70 among a plurality of switches (winker switch, horn switch, etc.) arranged in the vicinity of a user who has sat on the driver seat of the vehicle (100B) request signal generation means (80, a transmission circuit (46), and a transmission antenna (72), means for detecting a response signal from the electronic key (12) a reception circuit (44 and response signal matching means (82), and monitoring means (84) for outputting a lock release instruction to a actuator (64) when the response signal shows that the request is from a regular user.

要约 一种控制装置(14)包括：响应安置在坐在车辆(100B)的驾驶员座位上的用户附近中的多个开关(方向灯开关、喇叭开关等)的预定开关启动开关(70的ON操作而将请求信号输出到电子密钥(12)的装置请求信号产生装置(80传输电路(46)和传输天线(72)；用于检测来自电子密钥(12)的响应信号的装置接收电路(44、和响应信号匹配装置(82)；以及用于当响应信号显示请求是来自正常的用户时将锁定释放指令输出到执行器(64)的监测装置(84)。

Main product of automation control: various of industrial automation control equipments; PLC Cupboard; frequency conversion cabinet; constant Voltage water supply system; computer machine room and electromagnetic room environment intelligent control system; temperature and humidity controller; XK serious signal controller; elevator group supervisory control system; intelligent lighting contro system; hydroelectric power station gate control system; The implementation automation controlling tasks with the Single Chip Microcomputer development and Line Communication is hardware and software system adjustment and testing designated unit of domestic waste heat generating project.

自动化控制分部主要产品有：各种工业自动化控制设备；PLC柜；变频启动控制柜；恒压供水系统；机房和变电室环境智能化控制系统；温湿度控制仪；XK系列信号控制仪；电梯群控系统；智能化照明控制系统；水电站闸门控制系统；利用工业单片机的开发和载波通讯技术实现各种自动化控制任务。是国内余热发电项目软硬件定点系统调试单位。

The introductive robot arm of this text can output two lines pulses by the PLC, driving the horizontal stalk, and the perpendicular stalk to drive the electrical engineering actuator respectively, to control the robot arm precision of the horizontal stalk and perpendicular stalk at the fixed position, tiny move switch input the position signal to the PLC.The direct current motor drags along to begin the claw and bedrocks to revolve, the position signal from revolve the code dish and near to the switch feedback to host of PLC;The electromagnetism valve control the machine hand open and close, thus carry out the function of the machine hand precision work.

本文介绍的机械手是由PLC输出两路脉冲，分别驱动横轴、竖轴步进电机驱动器，控制机械手横轴和竖轴的精确定位，微动开关将位置信号传给PLC主机；直流电机拖动手爪和底盘旋转，位置信号由旋转码盘和接近开关反馈给PLC主机；电磁阀控制气开阀的开关来控制机械手手爪的张合，从而实现机械手精确运动的功能。

To facilitate this review an S-Paramics model was used to test several options. These options included removing signals at some junctions while relating pedestrian crossings, adding signals at a currently un-signalised junction, implementing active signal control and, finally, building a roundabout to replace a major signalised junction.

现使用S-Paramics模型对各种改善措施进行测试，包括1）把部分信号化交叉口改为非信号化交叉口；2）对一个非信号化交叉口信号化；3）实行主动信号控制；4）把一个主要信号交叉口改为环型交叉口等。

It can control the signal light with its internal project; also the user can modify the project by the control panel. And the outstanding point is that the intelligent traffic signal machine has the function of long-distance stakeout and control. Namely the intelligent traffic signal machine can transmit the real time traffic data to the upper computer and display the data on computer. The upper computer can modify and transmit the traffic data to the signal machine, improving the efficiency of the traffic control. The system realizes the function of communication by the TCP/IP protocol, and the capability is very good in reliability and real time.

本信号机能够运行内部的固有方案控制交通信号灯，同时可以通过键盘面板对方案进行修改，其突出特点是具备远程监控功能，即信号机能够实时将路口交通方案信息反馈给监控中心并在主控界面显示出来，监控中心可根据路口实际情况对现行交通方案进行修改，通过以太网下传给路口信号机，改善交通流量控制。

Aiming to solve the shortcoming in the prior art that any on-line DCF dispersion compensation technology is not provided for long distance, and the nonlinear effect in the dispersion compensation technology is restrained, the invention provides the dispersion compensation method, which includes the steps that after a sending end implements electric pre-compensation treatment on a digital signal to be transmitted, a control electric/optical converter module outputs a distorted optical signal; after receiving the optical signal, a receiving end conducts a post compensation treatment after converting the optical signal into an electric signal, or converts the optical signal into the electric signal after implementing the post compensation treatment.

为了解决现有技术中长距离无在线DCF色散补偿技术的不足和抑制色散补偿技术中的非线性效应，本发明提供了一种色散补偿方法，包括发送端将待发射的数字信号进行电预补偿处理后，控制电/光转换模块输出畸变光信号，接收端收到光信号后，将光信号转换为电信号后进行后补偿处理，或将光信号进行后补偿处理后转换为电信号的步骤。

Dynamic large-signal, DC, and small-signal circuit models including parasitic resistances and current ripples of nonideal synchronous rectifier buck converter operating in CCM are established. Closed-loop modeling of nonideal synchronous rectifier buck converter for voltage-mode control is studied. Transfer functions are obtained. Effects of parasitic components on control loop design of the converter are explored. Systematic simulation analysis is performed. All the results show that it is necessary to include parasitic components of converters into equivalent models.

首次建立了考虑寄生电阻和电流纹波的同步整流 Buck 变换器在连续工作模式下的大信号平均模型、DC 和小信号电路模型，研究了电压控制的闭环建模，导出了传递函数，剖析了变换器的寄生参数对其控制电路设计的影响，进行了小信号特性的仿真研究，进一步阐明了考虑变换器的寄生参数建模的必要性。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。