接触问题

I now have a computer with this problem, AGP slot is loose, not the ordinary graphics cards and point of contact inside the contact, so there is no way to show that several times to re-inserted after the position accurately do.

我现在用的电脑就有这样的问题，AGP槽很松，显卡的金手指不能和槽内的接触点接触，这样就没办法显示，要重新插过几次后，找准方位才行。

In these two models,it issuggested that the method of the stiffness matrix symmetrize for the state of sliding contact in orderto making use of FEM's resolver,resolving the large problems,lowering computer memory spaceand increasing efficiency.

在上述两种接触单元模型中，为了利用FEM软件包的求解器，为了解决大型问题，降低计算机内存占有量，提高机器效率，对于滑动接触状态提出了一种使刚度矩阵对称化的方法。

The research on the information security of the intelligent water meter has been done.

开展了对非接触式IC卡智能水表系统的安全性研究，在密钥管理方式上采用了一个基于非接触式IC卡的两级管理三次分散的密钥管理模型，解决了密钥生成、发行和存储等方面的安全问题。

According to the problem of outlet leakage of propane on the propane pump mechanical seal in the olefine factory of Qilu petro-chemical company, the new-type assembling non-contacting mechanical seal for propane pump was developed firstly on the basis of the principle of non-contacting of mechanical seal .

针对齐鲁石化公司烯烃厂丙烷泵机械密封频繁出现汽喷现象、密封端面泄漏严重的问题，根据非接触式机械密封原理，研制开发出了丙烷泵用新型非接触式机械密封。

I realise it is fashionable to be sniffy about Wikipedia, but on colds it is surely sound in stating categorically that you do not get them from being cold.

我们所有人无时无刻不在接触感冒细菌，因此问题不是如何防止接触，而是如何让自己不那么容易就向细菌举白旗。

The question of ruined earth pressure cell in test is solved,and the contact pressure between soil and pile is found out by the numerical simulation and distributing law of earth pressure.

通过数值模拟，解决试验中土压力盒损坏的问题，得到地震动激励下桩–土接触压力峰值的数据，并由此分析桩–土接触压力的大小及其分布规律，提出桩基上的支盘是基础减振的主要构件，并承受动荷载，减轻地震波对上部结构的冲击力，同时消耗上部结构反馈给基础的振动能量。承台和桩基两侧的土压力时程曲线呈反向关系，说明基础在同一时间一侧受压，另一侧受拉。

The research on the information security of the intelligent gas meter has been done.

开展了对非接触式IC卡智能煤气表系统的安全性研究，在密钥管理方式上采用了一个基于非接触式IC卡的两级管理三次分散的密钥管理模型，解决了密钥生成、发行和存储等方面的安全问题。

In order to deeply reveal the smoothing mechanism of roller burnishing and to overcome the difficulty in the selection of the burnishing cross feed dependent mainly upon experiences and hand feel, the roller burnishing process is taken as an issue of plane-strain mechanics and the micro-plastic deformation area is determined on the basis of the Von-Mises yield criterion and by using the Boussinesq-Flamant solution. Then, the contact pressure distribution is obtained based on the Hertz contact theory, and the stress distributions in the burnishing tool and the workpiece are respectively revealed.

为深入了解滚柱滚压表面光整机理，解决目前滚压量选择完全凭经验和手感的不足，将滚柱滚压加工过程视为平面应变力学情形，利用Boussinesq-Flamant问题的求解并根据Von-Mises屈服准则得出了滚压局部发生微塑性变形的区域，根据Hertz接触理论得出了滚压接触压力分布及滚压过程中工件和工具的应力分布。

Straight organ government purchases the small-sized machine that some abroad brand uses all the time before the center in, do not have too intimate contact to tide, 2004 the first time after buying tide server, in the process that contacts in sequel and tide service, expert, professional, cause effect " 360 ° expert serves " established a client to be opposite thoroughly the confidence of tide brand. In August 2005, run stable all the time tide NF420 to appear not to time maize lamp calls the police, after customer service center receives a phone to seek advice, rapid arrangement Beijing divides central expert engineer to come to detect, rapid fixed position gives the parent of the problem, give in time eliminate. In June 2006, area of the whole nation of customer service center that start is active pay a return visit, the engineer comes actively in visitting, straight organ government purchases a center, the server that is in to the client did health to detect, installed RAID to block the management such as monitoring program the software, backup strategy that is in to the client, safeguard log, UPS allocation to wait...

中直机关政府采购中心之前一直使用某国外品牌的小型机，对浪潮并没有太深的接触，2004年初次购买浪潮服务器后，在后续和浪潮服务接触的过程中，专家、专业、致效的&360°专家服务&彻底树立了客户对浪潮品牌的信心。2005年8月，运行一直稳定的浪潮NF420出现不定时黄色灯报警，客服中心接到电话咨询后，迅速布置北京分中心专家工程师上门检测，迅速定位出新问题的根源，并及时予以排除。2006年6月，客服中心启动全国区域主动回访，工程师主动上门拜访中直机关政府采购中心，对客户处的服务器做了健康检测，安装了RAID卡监控程序等管理软件、对客户处的备份策略、维护日志、UPS分配等给。。。

In order to solve the problems of which the spiral bevel gear of Oerlikon type is necessary to out and modify repeatedly, a new method was developed to predict the contact pattern and greatly reduce the cost for manufacturing by means of building a tooth

摘要为解决奥利康锥齿轮加工过程中需要反复试切、修正的问题，根据奥利康SKM2机床建立了加工延伸外摆线齿锥齿轮和准双曲面齿轮的齿面接触分析模型，提出了一种可预测齿面接触质量、降低设计加工成本的新方法。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。