接触

A dance position where the leader's left side and the follower's right side are in contact or almost in contact, and the opposite sides of their bodies are open in a V-Shaped position, leader looking right and follower looking left.

男士的左侧与女士的右侧接触或几乎接触，两人身体另一侧打开呈V字形位置，引导者在右，跟随者在左，是PP的反向位置。

A dance position where the leader's left side and the follower's right side are in contact or almost in contact, and the opposite sides of their bodies are open in a V-Shaped position, leader looking right and follower looking left.

Counter Promenade Position 反行进位置：男士的左侧与女士的右侧接触或几乎接触，两人身体另一侧打开呈V字形位置，引导者在右，跟随者在左，是PP的反向位置。

This paper presents two methods to estimate the relationship between dent depth and contact force, respectivelyβamend method and deflection compensate method, which are developed by using a clear geometrical relation to express indent, incursion profile and deflection difference.

本文以一种新的观点，用一个明确的几何关系来确定压痕、压头与板的接触面剖面及接触中心点与边界点之间的挠度差三者之间的关系，提出两种近似预测接触力与压痕深度关系的方法——β修正法和挠度补偿法。

From FEM, the contact stress obeys the semi-ellipse distribution and the Mises stress and shear stress are also consistent with contact mechanics theory, but there exists offset or deflection in the symmetric lines of stress distribution, which originates from tooth bending deformation.

由有限元方法得到的渐开线轮齿的接触应力符合Hertz理论中的半椭圆分布规律，Mises应力和剪应力分布也符合接触力学理论，但应力分布的对称中心存在偏离或者偏斜现象，分析认为，是由于轮齿弯曲变形造成的。

The results show that the ultrasonic wire bonding between the CZT contact electrode and the down-lead wire is easier to realize when the CZT wafers are mechanically polished and their contact electrodes are prepared by ion sputter technology.

摘 要：为实现高电阻CdZnTe半导体接触电极与外引线的超声波焊接，采用正交实验法探讨CZT接触电极与引线超声波焊接质量的影响因素及其作用规律。

The question of ruined earth pressure cell in test is solved,and the contact pressure between soil and pile is found out by the numerical simulation and distributing law of earth pressure.

通过数值模拟，解决试验中土压力盒损坏的问题，得到地震动激励下桩–土接触压力峰值的数据，并由此分析桩–土接触压力的大小及其分布规律，提出桩基上的支盘是基础减振的主要构件，并承受动荷载，减轻地震波对上部结构的冲击力，同时消耗上部结构反馈给基础的振动能量。承台和桩基两侧的土压力时程曲线呈反向关系，说明基础在同一时间一侧受压，另一侧受拉。

Occurs when the semi-finished, warping, especially the post-mounted corrugrted semi-finished products, immediately after the closing of embossing plate, on the paper--and there is no uniform die to tilt paper with the sponge rubber or contact, so easily make embossing plate produced by 印张 bliding, die-cutting production phenomenon.

当半成品出现卷曲、起翘情况时，特别是经过裱贴以后的瓦楞纸板半成品，放在压印平板上合压时，纸面与模切版没有均匀接触，使翘起的纸面先与版面上的橡胶条或海绵接触，这样容易使压印平板上的半成品印张产生滑移现象，造成产品模切不准。

Objective: Ultrasound is considered as an alternative enedrgy for post-myocardial infarction ventricular tachycardia due to its good penetration through tissues. This study was designed to observe the effects of acoustic power, duration, repetitive ablations, tissue-transducer interface temperature and different sites of the ultrasound ablation in vitro.

使用1.8 MHz超声，分别对①离体犬心肌标本：a采用不同的声功率、时间、次数进行消融，部分标本在消融测量换能器—组织间温度；b采用相同频率和声功率消融左、右心室肌；c 采用与组织接触和不直接接触的两种超声换能器消融；标本均以甲醛固定1～2周后测量损伤灶深度及体积。

I will not make friends with those who won't do me good and I will learn to make friends selectively and get rid of those who are not well-behaved as well as those beatniks on the street.

不结交对自己不利旳好友，有选择性旳交好友，不与对自己不利旳学生接触。不和社会上旳不良青年接触。

Arc cutting;Arc welding;Arc-welding equipment;Blowpipes;Burners;Construction requirements;Contact safety devices;Cutoff device;Cutting;Definition;Definitions;Dimensioning;Electric contact protection;Electrical engineering;Electrical safety;Equipment;Impact strength;Insulating resistance;MAG welding;Manual arc welding;Manual operation;Marking;MIG welding;Operating instructions;Plasma arc cutting;Plasma-arc welding;Protection against electric shocks;Protective measures;Safety engineering;Safety requirements;Specification;Temperature-rise tests;Test value;Testing;Testing conditions;Thermal;Thermal stress;TIG welding;Welding;Welding engineering;Welding equipment;Welding power supply

中文标题电弧焊接设备。焊炬中文主题词电弧切割；电弧焊接；电弧焊接设备；焊枪；燃烧器；结构要求；接触安全装置；切割装置；切削；定义；尺寸选定；电接触保护；电气工程；电气安全；设备；冲击强度；绝缘电阻；MAG 焊接；电弧焊操作手册；手控；作标记；金属极惰气保护焊；操作说明书；等离子体电弧切割；等离子电弧焊；防电击；保护措施；安全工程；安全要求；规范；温升试验；试验值；测试；测试条件；热的；热应力；钨极惰性气体保护焊；焊接；焊接工程；焊接设备；焊接电源

She gently rebuff ed him, but agreed that they could be friends

她婉言拒绝了，但同意作为朋友相处。

If in the penal farm, you were sure to be criticized.

要是在劳改农场，你等着挨绳子吧！