接触...

The results show as follows: Due to unfitting between the wheel tread and profile of Frog No. 9, two-point contact occurs between the wheelset and frog and the contact patches become narrow and long; the Von Mises stress and contact force in the area of the contact patch between the tread close to the flange and the frog are so great that they go far beyond the yielding limit and enter the plastic deformation stage; this will lead to serious wearing of wheelset treads and frogs.

结果表明，由于车轮踏面与9号辙叉的型面不配合，轮对与辙叉形成两点接触，且接触斑狭长，靠近轮缘处踏面和辙叉接触斑的应力及接触力非常大，其数值远远超过材料的屈服极限，进入塑性变形阶段，这将导致车轮踏面与辙叉的磨耗严重。

When it is used to solve contact problems,multiplepairs of contact points can be updated in each iteration,other thansome methods such as Thail-Van de Panne method and Goldfarb-Idnani method,which update only one pair of contact points at eachiteration.

用拟有效集方法解接触问题，每次迭代可以更换一组接触点对而不是某些方法只能更换一个接触点对，因此大大提高了解接触问题的效率。

Firstly, the paper introduced the working principle and device of the two-pass grate-rotary kiln and had an analysis method of mechanics of the tyre. We have put forward the finite element analysis of the contact stress of the tyre-roller based on the whole construction mode of shell-kiln liner-large gear-tyre-roller of the rotary kiln and obtained the strength and distributing rule of the tyre's contact stress. The research shows that within one week the contact stress mainly lies in two leading peak value and catastrophe which appear at the contact zone of the tyre and supporting roller. Then we regarded the tyre's stress as the test of unknown plane stress of principal stress. Utilizing mature and modern testing technology, we raised the testing principle and scheme of tyre stress and then had a on-the-spot test of the stress. Comparing the analysis result of the test with the one calculated from the finite element analysis, it proofed the rationality of finite element analysis method of integral modeling and the correctness of the contact stress result of the tyre and roller. Finally, for two-pass of similar rotary kilns, using the ANSYS APDL re-development technology, carried on the re-development about the overall finite element analytic method of thecontact stress of tyre-roller.

首先，本文介绍了2档回转窑的工作原理和装置，对滚圈的力学行为进行了分析，提出了基于筒体-滚圈-托轮的回转窑整体建模的有限元分析法，来对滚圈-托轮的接触应力进行有限元分析与计算，得到了滚圈接触应力的大小和分布规律，并求得滚圈外中内圈节点的主应力；其次，把滚圈的受力看成是主应力未知的平面应力的测试，利用现代测试技术，提出了滚圈主应力测试的原理和方案，并对滚圈的主应力进行了现场测试，现场测试分析结果与有限元分析计算出的主应力相比较，证明了整体法建模的有限元分析方法的合理性和滚圈-托轮接触应力结果的正确性；最后，利用ANSYS的APDL的二次开发技术，针对2档同类回转窑，就滚圈-托轮接触应力的整体有限元分析法进行了二次开发。

The temperature of connection was measured using infra-red thermometer and contact resistance of connection was measured using circuit resistance tester.

介绍两种判断电机电气连接故障的新方法，用红外测温仪测试连接点温度，用回路电阻测试仪对接触点接触电阻进行测试，能直观地反映出接触点温度、接触电阻大小，该方法方便、准确、实用。

Took the different diameters double-row bearing slewing ring asexample, this dissertation studied the distribution of axial press ofthe rolling body under axial load and throw moment, the contact pressbetween two outer seat-rings which are connected to the main machinewith high strength screw bolts.

本文以双排异径球式回转支承为例，对球式回转支承在承受轴向载荷和倾翻力矩时的滚动体轴向正压力大小、分布及由高强度螺栓与主机连接的滚圈接触面的接触力进行了详细的理论推导和实际计算，说明在双排球式回转支承的结构静力分析过程中，可以将滚圈安装接触面的接触力简化为铅垂方向的均布载荷。

Main job is to guarantee the scraping interaction and equipment on both sides of the friction surface or can obtain higher precision and accuracy, precision and shape accuracy, precision and contact transmission because of good lubrication, manual and repeatedly is worthy, large amounts of wind, time-consuming, scraping the time needed for different devices vary, such as boring slider and slide block wind profiling, between the match before measuring clearance between the original value, and then according to the technical requirement to measure the value of time and scraping scraping, then apply DanFen red on the slider, manual let slip on the slide seat back and forth, they do straight-line movement between full contact and friction, reoccupy scraper scraping friction creates the contact point, so repeatedly, until the technical requirements for the match, single within 2 days, must blow to the boring if all the time to work with wind, a half month is required.

刮削过程。刮削工作主要是为了保证设备相互接触并摩擦的两面间能获得较高的尺寸精度、形状精度、位置精度、接触精度、传动精度和良好的润滑，因是手工操作且需反复配刮，故工作量大，耗时较长，设备不同，刮削所需时间也各不相同，例如镗床上滑座与下滑座间的配刮，刮削前先测量出二者之间原有的间隙值，然后根据工艺要求测算出需刮削值及每次的刮削量，再将红丹粉涂于上滑座之上，手工让上滑座在下滑座上来回做直线运动，使它们之间充分接触和摩擦，再用刮刀刮削摩擦产生出的接触点，如此反复多次，直至技术要求范围之内，单此项配刮需2天左右，若对于整个镗床所有配刮工作的时间总和，则需半个月左右。

A model to describe the motion of contact line and dynamic contact angle on rough solid surfaces was proposed.

提出一个粗糙表面上移动接触线和动态接触角的数理模型：毛细数较低时表观接触线前缘存在极薄的前驱膜，表观接触线在"湿"固体表面上移动，不同于传统模型中认为表观接触线在"干"固体表面上移动。

Methods:54 workers exposed to styrene were selected as exposure group,25 workers unexposed as control group were similar like workers exposed styrene in age and sex.

选择接触苯乙烯工人54人为接触组，选择年龄、性别构成与接触组相似的不接触遗传毒物的工人25人为对照组。

Then the weak formulation of the control equations considering the contact constraint conditions has been developed. Combined the Lagrange multiplier and penalty function methods, the augmented Lagrangian method is used to treat the contact constraint and solved the non-linear and non-smooth problems of the mechanical response perfectly. A finite element model has been applied for the test project of the reinforced slope and to study the mechanism of the interaction of the soil and reinforced material.

本文在Lagrangian网格的控制方程中引入接触界面条件，并采用了经典的Coulomb摩擦模型作为界面切向面力的本构模型，继而发展了考虑接触约束条件的控制方程的弱形式；在求解方法上，综合了Lagrange乘子法与罚方法的优点，采用增广的Lagrangian方法处理接触界面约束，很好地解决了接触问题中的高度非线性和响应不平滑性。

Especially when dorsiflexion 20 degree goes to dorsiflexion 30 degree ,the contact stress arises 38%; when dorsiflexion 30 degree goes to dorsiflexion 40 degree ,it makes the contact stress arises 32%; when plantar flexion 20 degree goes to plantar flexion 30 degree ,it makes the contact stress arises 62%; when plantar flexion 30 degree goes to plantar flexion 40 degree ,the contact stress arises 23%.

由背屈20度变换成背屈30度时，其接触压力上升38%，由背屈30度变换成背屈40度时，其接触压力上升了32 %；掌屈20度变换成掌屈30度时，其接触压力上升了62%，由掌屈30度变换成掌屈40度时，其接触压力上升了23 %，与文献所载之趋势亦有相似之处。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。