接线的

It also has core technology of sink mark vent and welding line which are important to surface of bumper door panel and instrument board.

在缩痕、排气和熔接线问题的解决上也取得了核心技术，从而使保险杠、仪表板、门板等汽车主要部件的表面质量有了质的飞跃，再加上高品质标准件的大量运用，模具生产周期大大缩短。

If everything was ok,first test the test circuit without load in the conditions of parts to be tested not being connected,the test voltage will be increased by stages according rated voltage,each stage will be kept for 1 minute, write down the measurement values of microampere meter,then reduce voltage to zero and switch off power,make discharging for phase tested, measure insulation resistance for the other two phases.

并对被试相放电后，改接线测量另两相的绝缘电阻。在规定的试验电压下，各相泄漏电流的差别应不大于最小值的 100%。

The reason of unbalanced load voltage for station transformer in 220 kV substation was analyzed,the important influence of null line wirings in three-phase four-wire system on three-phase load voltage balancing was explained,and put forward a kind of simple,visual and practical vector analysis method.

分析一220kV变电站站用变压器负荷电压不平衡的原因，说明了三相四线制中的零线接线准确与否对负荷三相电压平衡性的重要影响，并提出了一种简单、直观的实用矢量图分析方法。

This article is based on cases analysis in production,explaining the reason on false connection of the phase and phase sequence lead to losses of electric power system,enterprise and daily work.

本文以生产中的实例分析为切入点，说明因相位、相序接线错误给电力系统、企业及日常工作造成的损失，并介绍几种预防相序错误的方法，为提高企业经济效益打下坚实的基础。

Along with the development of science and technology, single machine capacity of generator is extending continuously, it needs higher requests to connect the line form and the kit equipments of the power station, also request the power plant to attain the credibility, economy, reasonable movement, also satisfy the people's basic need that is the electric power.

随着国民经济和科学技术的发展，发电机单机容量在不断扩大，这就对电厂的主接线形式和配套设备提出了更高的要求，同时也要求发电厂做到可靠、经济、合理地运行，满足人们对电能的基本需求。

Design a complete set of stage lighting control system for the hardware and paint a complete circuit diagram of principle, schematics and wiring diagram.

设计一套完整的舞台灯光控制系统的的硬件电路并画出完整的原理框图、原理图及接线图。

The starter also be designed 6-3 binding post according to power. after finishing the installation, pls connect the line to corresponding location of binding post.

起动器装配完成后，将转子的出线接在起动器接线柱对应位置（对于有六根出线的电动机，应将同一相的两根导线，对称地接在起动器的两个接线柱上）即可，具体接线如下图所示。

INSTALLATION AND CONNECTION 1、Removing all parts of cover、rings、carbon brush、brush box、brush box shell and short circuit ring equipment(some motor have no short circuit ring equipment).

起动器装配完成后，将转子的出线接在起动器接线柱对应位置(对于有六根出线的电动机，应将同一相的两根导线，接在同一色的两个接线柱上)即可，具体接线如下图所示。

Founded in 1977 as a trading company with imported wire accessories for local manufacturing industries, Logistic aims to be the most comprehensive stockist distributor by continuously diversifying our product portfolio covering fasteners, insulators, connectors, PCB cable management accessories and parts, honing equipment, industrial brushes and marine parts, etc...

成立于1977年的洛士，专业从事接线辅助零部件的贸易工作。致力于为制造工业提供最多样化的产品，涉及固定件，绝缘件，连接器，PCB上用的布线器材和配件，研磨设备，工业毛刷和马达零件等。

In the project of mechanical structure,we bat around the error and metrical way of Crank Shaft,describe the elements of the Synthetically Measure Instrument Of Crank Shaft and the way to realize it. In the project of hardware"s control,we analyze the displacement sensor,the data acquisition card,stepping-motor and it"s controller.

在硬件的控制部分，我们主要对所用的位移传感器和数据采集卡、以及步进电机及其驱动器进行了分析，并提出了硬件控制部分的设计方案，进行了硬件控制部分的接线、调试工作。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。