接线

A kind of new method for daily checking wire rope is introduced, which checks the state of wire rope by means of a circuit consisting of one electrical source, one amperemeter, two connecting buttons, a piece of conducting wire and one thermometer.

介绍了一种日检钢丝绳的新方法，该方法通过一个由电源，电流表，接线扣，导线和温度计组成的电路来检查钢丝绳的状况。

Open the wiring terminal cover of detector (can be performed in the installation of detector), connect amperemeter to No.3 terminal, the heating current of the terminal should comply with the following requirements

打开探测器的接线端子盒，3号端子串入电流表

In the design part of the PLC control, the paper has explained the design process of the PLC I/O hookup, provided the choice result of the PLC and the PLC I/O elements, and has explained the design process of the PLC user program in detail, which includes the exposition to the design process of the public program, manual program, autoloading program signal showing and trouble alarm program.

在PLC控制的设计部分中，阐述了PLC I/O接线图的设计过程，给出PLC及其输入/输出元件的选择结果，详细地阐述了PLC用户程序的设计过程，其中包括对公用程序、手动程序、自动程序、信号显示与故障报警程序的设计过程的阐述。

Staking Adhesive / SMT Connections Chip Componts-Bottom Only Terminations / Chip Components-Rectangular or Square End Components-1,3 or 5 Side Termination / Cylindrical End Cap(MELF Termination / Castellated Terminations / Flat Ribbon, L, and Gull Wing Leads / Round or Flattened Leads / J leads / Butt/ I Connections / Flat Lug Leads / Tall Profile Components Having Bottom Only Terminations / Inward Formed L-Shaped Ribbon Leads / Surface Mount Area Array / Plastic Quad Flat Pack-No Leads / Components with Bottom Thermal Plane Terminations.

胶水粘接、SMT连接（底部焊垫片式元件、1-3-5片式元件、圆拄型、城堡型、鸥翼型引脚、圆形或扁圆型引脚、J型、I型、扁平焊片、高立底部焊垫、内L型、BGA、PQFN等引脚形态）、跨接线等。

Our primary products are: RCA receptacle, WP outer receptacle, 6.35, 3.5, 2.5 coaxal socket, S terminal, connecting parts, touch switch, power switch, USB connector, 21(42) pin receptacle, FFC/FPC flat cable connector etc.

主要产品有RCA插座NWP外接线插座﹐6.35N3.5N2.5同芯插口﹐S端子﹐接插件﹐轻触开关N电源开关﹐USB接口N21（42）针插座﹐FFC/FPC扁平电缆连接器等300余种。

2 Dead metal parts of a device provided with a socket contact or terminal identified for use as an equipment-grounding conductor shall be conductively connected to the grounding-conductor path.

9.2 一个配有插孔接触件或确定用作设备接地导线的接线端子的器件，它的不带电零件应被导电地连接到接地导线通路。

Connection elbow s have been produced by an easy operation that horizontal cluster casting with core_up moulding technology has been adopted which consists of water glass and lime sand cured by CO2 for molding and coremaking with reasonably selected method while feeding through making the most of gating, hence all performance targets of products meeting desired technical requirements.

采用水玻璃石灰石砂CO_2硬化制型、芯，合理选择造型方法，采用组芯水平串铸工艺，充分利用浇道补缩铸件，生产操作方便，所获得的接线弯头性能等各项指标，均达到技术要求。

Moreover, the use of DCB not only permits the disconnector to be eliminated, but also allows the busbar topology to be improved.

此外，DCB 的使用不仅取消了隔离开关，而且还可以改进主接线方式。

Each pole has two insulation supporters that dividedly fixed on the bushing of base's two sides (Figure 2), with links by rod. Each insulation supporter can horizontally rotate and the angle is 90°. The conductive wiring block (Figure 3) and left/right contactors (Figure 4) on the insulation supporter.

每极有两个绝缘支柱分别固定在底座两端的衬套上(图2)、以连杆连结，每个绝缘支柱可以水平旋转，转角为90°，绝缘支柱上装有导电接线座(图3)、左、右触头(图4)。

When the System installation was finish, Please confirm the wiring is errorless, and follow the arrow point (you can see it from the "Urgency Stop" button) that instruct the direction to rotate this button gently, button will spring outwards, push " power" button on B-case and check it is working, the

系统安装完毕，并确认接线无误，可按B柜操作面板上&急停按钮&的箭头指示方向轻轻地转动该按钮，按钮会向外弹出，按下B柜上&总电源开&按钮，系统得电，&总电源开&指示灯亮，按B柜上空压机按钮，可以实现空压机的启动/停止控制。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。