排放阀

A kind of nozzle body sensor based on magnetoelectricity and relative system with a machine of AT89C51 has been designed in order to master the spraying course of the injector and its injection regulation accurately, study and improve combustion chamber and intake, control the burning course of the fuel well, so that we can both reduce the consumption and decrease the amount of exhaust gas.

为了能够准确地掌握喷油器的燃油喷射过程和喷射规律，以研究和改进燃烧室及气道，组织好燃油的燃烧过程，降低油耗和减少尾气排放，设计了一种基于磁电式针阀升程传感器和以AT89C51单片机为核心的智能化针阀升程测试系统。

Open needle valve "B" to bleed air and then close "B" and vent needle valve.

开启针形阀"B"排放空气，然后关闭"B"和排气针形阀。

To avoid this discharge, install a spring-loaded, rubber seated check valve ahead of the backflow assembly.

为了避免这种排放，要在防回流阀总成前面安装一个弹簧驱动、橡胶阀座的止回阀。

To avoid this discharge, install a spring-loaded rubber seated check valve ahead of the backflow assembly to " lock-in " the downstream pressure.

为了避免这类排放，要在防回流阀总成前安装一个弹簧负载橡胶阀座止回阀来"锁定"下游压力。

Open needle valve "A" high side, then open needle valve "B" low side + turn, loosen hose at test cock No. 4 to remove air.

开启针形阀&A&高端，然后开启针形阀&B&低端，松开测试旋塞4号上的软管排放空气。

Open needle valve "A" high side, then open needle valve "B" low side one turn, loosen hose at test cock No.

开启针形阀&A&高端，然后开启针形阀&B&低端一圈，松开测试旋塞4号上的软管以排放空气。

When the condensed water discharge is completed, the subsequent emission of steam, due to condensation of water vapor than the volume and velocity, to generate pressure up and down the valve, the valve in the suction flow rate of steam rapidly closing.

当凝结水排放完毕，蒸汽随后排放，因蒸汽比凝结水的体积和流速大，使阀片上下产生压差，阀片在蒸汽流速的吸力下迅速关闭。

When the condensation of water discharge is completed, followed by emission of steam due to condensation of water vapor than the volume GLOBE VALVE and flow, causing the upper and lower valves generate pressure, the steam valve of the suction flow rapidly closing.

当凝结水排放完毕，蒸汽随后排放，因蒸汽比凝结水的体积和流速大，使阀片上下产生压差，阀片在蒸汽流速的吸力下迅速关闭。

Special emphasis should be put on the parallel connection of Venturi mixer, for it can avoid the stalling disadvantage of series-wound connection of Venturi mixer, enlarge the modulating range of EGR rate enormously, and make the best of Venturi mixer.

在前文建立的性能与排放综合预测模型基础上，增加简化的EGR管路流动模型，首次将排放预测与实时EGR管路流动结合起来，进行单向阀EGR系统的性能与排放综合预测。

2 The provisions of valve flap stent thrust nut in space; 4.3 will bring more than ejector stem components, and into the valve flap bracket, now can adjust screw ring on the injector; adjustment ring discharge pipe may be twisted too high in case of this case, when the valve assembly after the valve flap in contact with its seat before the valve flap seat will have an additional load on the adjustment ring edge, in order to avoid this from happening, should enable the adjustment ring hole just below the injector thread, through which holes should not be able to see thread.

4.2 规定阀瓣支架与止推螺母中的间隙； 4.3 将喷射器提起超过阀杆组件，并放到阀瓣支架上，现在可以把调节环拧在喷射器上；调节环可能在排放管上拧得太高，如遇此情况，当阀门组装后，在阀瓣与其座相接触前，阀瓣座将加载荷于调节环的边上，为了避免此情况的发生，应使调节环上的孔正好低于喷射器的螺纹，通过这些孔应不能看到螺纹。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。