挤压

US extrusion demand remains weak, with demand in the key end-use sectors of construction and transportation downbeat.

美国挤压需求仍显疲态，因建筑和运输这些重要的终端使用部门需求低迷。

The flow pattern of residual parts of duralumin billets, directly extruded at different temperatures, with or without, lubricants and with aluminum cladding or inversely ...

采用合适的润滑剂，毛坯外包纯铝薄套成反挤时，都可能消除坯料的表面局部塑性变形展，因此都能消除粗晶环和提高挤压制品的抗拉强度。

From casting, squeezing, aging treatment, air blast quenching, cold quenching to anode oxidation, we could process duralumin constructions, and provide you all kinds of pipes, sticks and profiled bar for industry, transportation, electronic, radiator, decoration and civil us

从熔炼铸造、型材挤压、时效处理、风冷淬火、水冷淬火到阳极氧化等各车间工序，可为您加工生产铝合金建筑、工业、交通、电子、散热器、装饰、民用等多种规格及状态的管、棒、异型材。

To improve its edibility and promote comprehensive utilization of soymean, twin-screw extrusion technology was used to deal with soybean meal.

为提高豆粕的可食性及大豆的综合利用率，本文利用双螺杆高湿挤压技术对豆粕进行深度组织化。

I guess the way that they may think twice to use extruding to kill eel.

我猜他们俩个可能想用挤压的方式把鳗鱼杀死。

Film or paper surface dirty, and wrapped it into the dust or clear plastic mulch films after the crease or relaxation phenomena, film hemming switched to a new membrane drying temperature is too high, adhesive surface crust adjust oven temperature, clear crusts partⅱ thermotolerance cohesion and not enough use better glue wrinkle of polymer-coated film transfer after the roll is not the proper balance of films at both ends are inconsistent or wave; adjustment layer of polymer-coated machine too thick, solvent evaporation incomplete, viscosity, pressure drum extrusion, paper (Business card printing and membership card making products) and films between slide to adjust the film covering technology electrothermic roll and rubber roller ends is not plain, pressure is inconsistent, ranging from the adjustment of the linear speed of the machine after the temperature inside the plastic mulch film covering the subject in yellow glue resin particularly resin or additives not resistant to ageing, in the light, heat, under the influence of ultraviolet radiation, chemical change, build the pigments should be switched to a new glue

薄膜或纸张表面不干净，裹入灰尘或杂质清除后再行覆膜薄膜有折皱或松驰现象，薄膜卷边换用新膜干燥温度过高，粘合剂表面结皮调整烘道温度，清除结皮胶的粘接力和耐热性不够换用更好的胶水覆膜后起皱薄膜传送辊是否不平衡；薄膜两端松紧不一致或波浪边；调整覆膜机器胶层过厚，溶剂蒸发不彻底，影响了粘度，受压力滚筒挤压，纸张与薄膜之间产生滑动调整覆膜工艺电热辊与橡胶辊两端不平、压力不一致、线速度不等调整覆膜机器覆膜后易变黄胶水中的主体树脂特别是一些增粘树脂或助剂不耐老化，在光、热、紫外线的影响下，发生化学变化，生成有色物质应换用新胶水

The structure optimization for the flat receptacle under the condition of ellipticity is proposed.

提出了椭圆度概念下的扁挤压筒结构优化思想。

But weather it is the same in the clinical,we will rearch and confirm in the clinical part of the topic. 2 Both extrusion embolectomy and Fogarty balloon catheter embolectomy had damage to the blood vessel endothelium to some extent.The injur was serious between 7 and 14 days,and then began to repair from 14 days.

2挤压患肢驱栓和Fogarty球囊导管取栓术对血管内皮均有不同程度的损伤，7～14天损伤较严重，14～28天开始缓慢修复，但是相比之下后者的损伤更为严重，修复也更不完全。

The results show that a slow stressing is suitable for the energy input and absorption.

结果表明，高压料层粉碎宜采用缓慢挤压，这样有利于高能输入和吸收。

Methods After enterotomy and decompression,the operator could squeeze the bowel by two hands for bowel clean.Without colonic larage,a little completely mashed the bowel content could continually pass primary anastomosis after inestines anastomosed.

肠切开减压后，用左右手交替挤压法清洁肠道，不灌洗肠腔，使肠吻合后吻合口处持续有少许较稀薄的肠内容物通过。

She gently rebuff ed him, but agreed that they could be friends

她婉言拒绝了，但同意作为朋友相处。

If in the penal farm, you were sure to be criticized.

要是在劳改农场，你等着挨绳子吧！