挤压
- 与 挤压 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
After those incisors had been extruded, a slight movement of the gingival margin in the same direction of the extruded teeth could be noted and an increase of the keratinized gingiva width was also recorded.
在那些已被挤压门牙,轻微运动,牙龈缘在同一方向的挤压牙齿可以注意到,增加的角化牙龈宽度也记录。
-
Through application of A-1 and A-2 in extruding pelleting system, also found that A-2 decreased power of pelleting system, current of gear pump and voltage more availability than A-1 in conclusion application of A-2 in peileting system could improve output of extruding pelleting system.
通过对A-1、A-2在挤压造粒工艺中的工业应用同样发现:A-2对降低混炼机功率,齿轮泵电流和压力都有帮助,能够达到提高挤压造粒系统负荷的目的。
-
This paper refits the 300 Copper Conform Machine's mold system to apply ECAP-Conform experiment.
本文根据ECAP的特点,对我院自行研制的TLJ300连续挤压机的工模具进行改装,用于连续等通道角挤压实验。
-
Three dimensional simulations were made in 5-hole nozzle s which were skived by fluild former and later by means of AVL FIRE software.
并在CA498柴油机上进行了5孔挤压研磨喷油嘴的对比试验研究,试验结果表明,挤压研磨喷油器在满足排放的前提下,改善了经济性指标。
-
Under the effect of compressive stress field, asymmetric in north-south direction, the Tianshan orogen upheaved quickly, and the southern part of Junggar basin subsides as it bent under the compressive action.
天山造山带快速隆起是南北向不对称挤压作用的结果,准噶尔盆地则在挤压作用下弯曲而发生沉降,形成南部坳陷区。
-
Production process: after casting, extrusion, tinting, electrophoresis, powder coating, fluorine carbon spraying, mould, polishing, wood, metal wiredrawing, such extrusion.
生产工艺:经过熔铸、挤压、氧化着色、电泳、粉末喷涂、氟碳喷涂、模具、抛光、木纹、拉丝、钣金等挤压而成。
-
From the angle critical force ,this thesis analyses the stability of the formation of axle shaft spline in the extrusion and the calculation of the constraints available after losing stability.
从临界力的角度入手分析花键半轴在挤压成形时的稳定性及失稳后可增加约束的计算,研究表明半轴花键实现精密挤压成形不稳定时可增加约束来解决失稳问题。
-
Working with taper billet heater plus isothermal extrusion provides good possibility to produce good and stable quality products.
铸棒的梯度加热,挤压筒温度的均匀控制,对中检测和调整、等压挤压、在线淬火等先进技术的应用将大大提高产品的精度和性能,可以生产出尺寸稳定,组织和性能均匀的高质量、高精度的产品,使金桥铝材再上一个新台阶。
-
Effects of varying screw speed, moisture content and feed rate on cottonseed meal de-gossypol result were studied using a twin-screw ext ruder and Response Surface Methodology was utilized to carry out the exper iment design and data processing.
林炳鉴 ,王洪武,周建国利用自行开发的双螺杆食品挤压机对棉籽粕进行挤压脱棉酚试验,考察了含水率、螺杆转速和喂料速度等参数对脱毒效果与挤出产量的影响。
-
The calculation of deformation force during steady state stage, as well as the design principles of the expansion feeder plate die is discussed.
分析了宽展挤压变形规律及宽展模具调节金属流动的机理,建立了宽展挤压流动模型。
- 推荐网络例句
-
On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.
另一方面,更重要的是由于城市住房是一种异质性产品。
-
Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.
气候直方图是将所收集的降水量测定值,分为几个相等的区间作为横轴,并将各区间内所测定值依所出现的次数累积而成的面积,用柱子排起来的图形,也叫做柱状图。
-
You rap, you know we are not so good at rapping, huh?
你唱吧,你也知道我们并不那么擅长说唱,对吧?