英语人>网络例句>挤出的 相关的搜索结果
网络例句

挤出的

与 挤出的 相关的网络例句 [注:此内容来源于网络,仅供参考]

Though feeling sad, Mary still gave me a reluctant smile.

虽然玛丽很难过,她仍然对我挤出一丝勉强的笑容。

Everyone wants a stake in the corporate action;no one can affort to be left out of the race.

每个人作为公司的一份子都要为竞争做出努力;任何人都不会被挤出竞争之外。

The raw material as clay enter the material box after vacuum clean ,will be molding bye the knife blow ,when change the different model ,it will make different type air brick .

泥土等原料通过真空净化后,进入受料箱,由下级绞刀挤出成型,当机口采用不同模型时,可生产各种规格的空心砖。

Then I will extrude the polygons and align them how I think is right.

然后我会挤出多边形,并调整他们如何,我认为是正确的。

In common glass fiber reinforced polyolefine pipe, when the volume faraction is less than the critical value, the glass fiber can not act as reinforcement, on the contray, it would reduce the whole intensity of the compound material. However, when extruded in combined stress field, the extend intensity of the compound system increases when the volume fraction of glass fibers is less than the critical value. When the glass fiber volume fraction is higher than the critical value, the required glass fiber volume fraction of compound fibers extruded in the combined stress field is less than theory value.

一般玻璃纤维增强管材在常规挤出时当添加的玻璃纤维体积含量小于临界体积分数(当添加的玻纤的复合体系拉伸强度等于基体聚合物材料的拉伸强度时的玻纤体积分数)时,玻纤起不到增强的作用,反而会使复合材料的整体强度降低;但在复合应力场下挤出时,当添加的玻纤含量小于临界体积分数时,复合体系的拉伸强度不但没有降低反而升高了;当添加的玻纤含量大于临界体积分数时,复合体系要达到同样强度,经过复合应力场的玻纤增强管材需要的体积分数小于理论值。

This article starts with the modificatory production function, establishes a new frame for theory analysis, based which this article then analyses the action mechanism of extrusion effects MNCs gives to China, and discusses the three different phases of MNCs'employment effects, namely absorb effects in short term, extrusion effects in medium term and draught affects in long term. Bases on the analysis, the article makes a new explanation of China's employment elasticity since China's reform and opening.

本文从修正的生产函数入手,构建了新的理论分析框架,在此基础上分析了跨国公司对国内就业的挤出效应的作用机制,论述了其就业效应的三个不同阶段,即短期的吸收效应、中期的挤出效应和长期的拉动效应,并在此基础上对改革开放以来中国就业弹性的变化做出了新的解释。

The results indicate that the interface curve in width varies along the flow direction. The flow rate ratio controls the coextrusion interface location. The interface deviate value increases with the increasing of the flow rate ratio. The difference viscosity of two layers polymer leads to the interface deflecting towards the lower viscosity side.

结果表明:宽度方向共挤出界面的形状和位置沿聚合物流动的方向不断变化;界面偏移量的大小随着流量差异的增加而增大;聚合物入口流量的变化是导致共挤出界面位置变化的决定性因素,流量比的变化对出口处界面形状的影响不大;两种聚合物粘度的不同会导致界面偏向粘度较低的熔体一侧。

Relying on both dynamic and static analysis methods,both microstructure and macrostructure analysis methods,both on-line and off-line analysis methods,as well as both along-line sampling and die sampling techniques,the author of this thesis studied and developed an on-line microscopic system,the on-line rheometers and the on-line samplers which are used in single screw extruding process for the first time. Based on the analyses of a plenty of experimental results, the thesis mainly discussed following several questions: solid-bed break-up phenomenon on macroscopic scale,melting and deforming mechanism of a solid particle on small particle scale,and polymer morphology on microscopic scale.

本文作者通过把动态和静态分析相结合、微观和宏观分析相结合、在线和非在线分析相结合、沿程取样和机头出口样品分析相结合的方法,在单螺杆挤出过程的在线显微观察与摄影、在线流变测试、在线取样的大量实验分析的基础上,针对挤出过程中从宏观尺度范围的固体床破碎现象、到较小的颗粒尺度范围的固体粒子的熔融与变形、以至微观尺度范围的聚合物材料的形态结构的变化情况等有关几个的问题进行研究讨论。

The three dimensional flow field in the triple-screw extruder with triangle configuration is the research objects of this task, including velocity field, pressure field and shear rate field etc., simulate the representative flow field in metering section of the triple-screw extruder, consisted of three-thread element with75mm pitch, has been simulated at the screw speed of 60, 120, 180, 240 and 300rpm and the flowing regulations in flow field and especially the role of the unique center zone affecting to the conveying and pressure generating ability have also been analyzed.

本课题以三角形排列的三螺杆挤出机三维流场为研究目标,研究内容包括速度场、压力场、剪切速率场等。模拟分析首先以螺距75mm的三头螺纹元件为代表,计算由其构成的三螺杆挤出机在60、120、180、240及300rpm转速下的流场,分析流动规律,并分析了特有的中心区在输送、建压方面的作用。

The work of this article is mainly focused on the following sections: 1)Detailed expatiated physical model of three sections and seven zones in extruding process of a single-screw extruder, and mathematical model of each zone and solutions to them.

本论文的研究工作主要集中在以下几个方面:较为详细的阐述了单螺杆挤出机挤出过程的三段、七区物理模型和各区段的数学模型及它们的求解方法。

第14/70页 首页 < ... 10 11 12 13 14 15 16 17 18 ... > 尾页
推荐网络例句

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发,分析对称连杆曲线上鲍尔点的产生条件,提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品,年生产总值3000万美元,产品价廉物美、选料上乘、质量保证,深受国内外客户的青睐

The eˉtiology of hemospermia is complicate,but almost of hemospermia are benign.

血精的原因很,以良性病变为主。