挠度

In box girders with deep sections, the initial deflection caused by the first pour, soffit and stem, is usually the total deflection for the system.

箱梁深路段，初挠度造成的首倒，檐口，茎秆通常总挠度的制度。

In the forth chapter, gained two relations, that is the relation between in original deflection and the critical stress and the relation between the total deflection and the load.

第四章通过和第三章除了板的加筋板位置不同，其余相同条件下的板的临界应力，得出了初挠度和临界荷载的关系以及总挠度和荷载的关系。

The above results are compared with the convergent solutions obtained by the method of trigonometric series.

计算结果表明，挠度幅值远远大于中面位移幅值，且与由双三角级数能量解法所得挠度幅值吻合很好。

Based on the calculation method of deflection of castellated beams ,this paper presents a practical reduced formula for deflection calculation.

在介绍蜂窝梁挠度计算的基础上，提出了一种实用简化的挠度计算方法，并通过3根蜂窝梁试验，验证了简化计算公式的可行性。

This paper discusses the problems of measuring for deflection of thermal bimetal element and puts forward a kind of method for optical measurement of thermal bimetal element.

讨论热双金属片挠度的测量问题，提出一种热双金属片挠度的光学测量方法。

A new bridge deflection measurement method was proposed, in which the geometric information of co-operant was acquired by using the surveying robot. The angle measurement precision and the distance measurement precision of surveying robot were analysed from two perspectives of systematic error and random error. The measurement error analysis was done by considering the effect of the vertical angle and stadia. Measurement precision of the method was analysed in the least square principle.

提出了一种以测量机器人为采集器，通过获取合作目标的几何信息进行桥梁挠度测量的新方法，从测量系统误差、偶然误差两个方面分析了测量机器人的测角及测距误差，并探讨了竖直角、视距付挠度测量误差的影响，同时依据最小二乘原理分析了该方法的测量精度。

This paper presents two methods to estimate the relationship between dent depth and contact force, respectivelyβamend method and deflection compensate method, which are developed by using a clear geometrical relation to express indent, incursion profile and deflection difference.

本文以一种新的观点，用一个明确的几何关系来确定压痕、压头与板的接触面剖面及接触中心点与边界点之间的挠度差三者之间的关系，提出两种近似预测接触力与压痕深度关系的方法——β修正法和挠度补偿法。

Deflection;bridge doctor software;a static-load test;deflection test Dial gauge

挠度；桥梁博士软件；静载试验；挠度测试百分表

It is very useful that large span space frame structuredeflection is calculated by this method.

此种方法特别适刚于较复杂的多层大跨度空间框架结构进行短期挠度的理论计算，并由此估算其长期挠度。

The superposition method in mechanics of material and a MATLAB Procedure was used to calculate the top deflection of tall tower under both of weight and wind pressure.

采用材料力学的叠加法和自编的MATLAB程序，计算了高塔设备在风载荷和自重联合作用下的塔顶静挠度，并推出了考虑自重影响时塔顶静挠度的计算公式。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。