拧松

Key components installed ink, adjust the blade support shaft section of copper Cap nut, the blade front-end on either side of half-round slot is placed in the kuyto specialadhesive Groove at the antileakage gum, tighten the screws, the installation is complete with rubber extrusion antileakage blade, the two-blade antileakage glue between the slot from semicrcular extpuded, producing gum in the column so that you can more effectively prevent ink seepage.

在安设不朱键组件时，调动不朱刀支架轴段的铜螺帽，不兵不朱刀前端两侧的半圆槽安插在托不活胶槽处的防漏胶上，拧不松变动螺丝，安设达成后用不朱刀挤压防漏胶，不兵两不朱刀之间的防漏胶从半圆槽洋挤出，爆发胶柱，这样不离可以更灵验不天避免油不朱渗漏。

And 6 intake valves. Tighten valve adjusting screw locknut to 27 N·m (20 lb-ft).

将气门调节螺丝防松螺母拧紧至27牛顿·米（20磅-英尺）。

For example , the use of a lock washer is acceptable to prevent the turning of a device having a single hole mounting means .

例如，使用的拧紧垫圈防止一个单孔安装情况下旋转松脱。

Xiao zhang, pass me the monkey wrenches, the safety nut is relaxed, I want to

小张，把活动板手递给我，这颗保险螺帽松了，我要把糨它拧紧。

Xiao zhang, pass me the monkey wrenches, the safety nut is relaxed, I want to tighten it up.

小张，把活动板手递给我，这颗保险螺帽松了，我要把糨它拧紧。

The invention relates to a nut (10) comprising an outer body (16) with an axial passage (22), an inner body which can be movably placed in the passage along an axial direction and which is divided along said axial direction into at least two jaws (18, 20), each jaw bearing an inner thread segment (24) on its radial inner surface, first guiding means (26) located on the outer body, as well as second guiding means (30) located on the jaws and co-operating with the first guiding means so that the jaws are radially displaced towards the exterior when the outer body is displaced in the unscrewing direction relatively to the inner body et radially displaced towards the inside when the outer body is displaced in the screwing direction relatively to the inner body.

本发明涉及一种螺母(10)，它包括：一个带轴向通孔(22)的外体(16)；一个内体，位于通孔(22)中，可沿轴向移动，并且沿所述的轴向方向至少分成两个滑块(18、20)，它们各自在其径向的内表面上具有内螺纹部分(24)。在外体上有第一导向装置(26)，同样滑块上有第二导向装置(30)，第二导向装置与第一导向装置共同起作用，所以，当外体相对于内体沿旋松方向作相对滑移时，滑块径向地向外滑移，并且，如果外体相对于内体沿拧紧的方向滑移，则滑块径向地向内滑移。

Power lines and power will board the connecting blocks, and then covered with electrical box and lock locking (Note: Do not pressure line), the final will be hanging hook screw into electrical boxes installed screw holes, tightening later M4 * 8 hanging hook-locking screw-tightening.

将电源线与电源板上的接线端子连接好，然后盖上电器盒并用锁扣锁紧，最后将吊勾拧入电器盒安装螺纹孔内，拧紧后用M4*8吊勾锁紧螺钉拧紧防松。

It has mainly actions as follows: accumulating steel wire; sending steel wire; drawing steel wire; clipping; tighten; squeezing flat; regulating position of strapper, etc; using annealed rod of φ6.5,φ6.0 or hot-finished rod ofφ6.0 directly as strapping steel wire; it straps and tightens for 720°,and then squeezing flat to make sure that it straps firm and not easily loose.

它具有如下主要动作：蓄丝、送丝、抽丝、剪断、拧紧、挤平、打捆机位置调节等；使用φ6.5，φ6.0的退火盘条或直接采用φ6.0的热轧盘条作捆丝；其捆结拧紧720°，然后挤平，保证了捆结牢固，不易松脱。

The international standard ISO 2320 specify 5 screwing and unscrewing.

国际标准 ISO 2320详述5次拧紧和旋松。

Then check the small antirotary counter-connected downtime of failure, heart-throbbing "" given and magnetic field with the hands turn drawer small motor rotor axis, the rotation were found jammed or deastringency todaya functionalbuffering be electrocircuit reasons, check the growth rate in the relay 2KJ tramsformer, the normally closed contact of the sighting of a tramsformer loosting, screw did not tighten, and pull-out, I found the head on the oxidi.

再查抄小电机在停机后不侧转不到位的障碍，拉不开&给不退与磁场&抽屉，用手转不静小电机的转子轴，未发掘卡住或转不静阻涩的本体，外明是电路的来因所致，查抄增速继电器2KJ的常不开触不面接线，发掘有一根接线松不静，螺丝不有拧不松，且不不收入后发掘线头上有氧化层。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了