拟合曲线

One is based on the B-spline fitting to the contours;the other computes the curvature directly taking advantage of the relation of curvature and osculating circle.

一是基于轮廓的B样条拟合，通过计算拟合B样条曲线在各采样点处的曲率估算轮廓点的曲率

This paper introduces the method of determining overburden pressure by using density logging data.

介绍了利用密度测井资料求取上覆岩层压力梯度的方法和步骤，并提出了一种更合理的拟合方程对上覆岩层压力梯度曲线进行拟合，以期获得更加合理的外推数据。

That the fitting residual errors are in the 1nm magnitude order,so the curve fitting algorithm can be used in the high-precision curve fitting exactly.

试验结果表明：该算法的拟合误差在1nm数量级，可用于完成高精度的数据曲线拟合。

The mean velocity distributions in turbulent boundary layers of smooth surface and two different riblet surfaces are measured with IFA300 constant-temperature anemometer in low-speed wind tunnel to validate the full development of turbulent boundary laye. Friction velocity and wall friction stress of turbulent boundary layer are obtained with the least-squares fitted curve of the sublayer velocity distribution based on Spalding formula, and virtual origin position of riblet surface can be acquired accurately.

在低速风洞中来流速度一定的情况下使用IFA300恒温热线风速仪测量了光滑表面和两种不同尺寸的脊状表面湍流边界层平均速度分布剖面，并验证了试验段湍流发展的充分性；通过应用Spalding壁面公式使用最小二乘法精准拟合了实验测量的边界层内层速度分布曲线，得到了湍流边界层壁面摩擦速度并进一步求得湍流壁面摩擦应力，较准确地计算出脊状表面的虚拟原点位置，并通过与对数律公式拟合结果比较分析，证实了该方法更加准确有效。

The surface of conventional engineering part is composed of simple analytical surfaces and four-boundary ruled surface primarily. Therefore a point cloud segmentation method based on those feature surfaces is proposed. Several algorithms to identify the simple analytical surface feature are investigated and discussed. The theory of fitting scattered point to B－Spline and Bézier surfaces is introduced and a fitting method based on four boundary and point set is also discussed. Moreover, anew method to recover the fix-radius rolling ball blend is proposed and discussed in detail.

常规工程零件的外表面中包含了大量的特征曲面，如简单解析曲面和四边直纹面，因此，本文提出基于特征曲面的的点云分割方法，研究几种识别简单解析曲面的算法；研究由点云拟合B－Spline和Bézier曲线的理论基础，总结曲面拟合的几种方法，提出一种反求定半径滚球圆角的方法。

P for short at different temperature was studied by using the method of predictive microbiology. Growth curves were obtained at 4~40℃. and foud that the Gompertz model fit at 10~40℃ with representation of experimental curves which are typical sigmoidal.

结果表明，在10~40℃，副溶血性菌弧的生长曲线呈典型的S形，适合用Gompertz和logistic模型拟合；当温度在4~10℃时，适合用线性回归方程拟合。

Finally, we adopt the fault smoothing constraint and dipping angles obtained from previous two steps and invert for the coseismic rupture distribution.

建模过程经历三个步骤：（1）采用直立断层模型反演，根据解的分辨率和拟合差的折中曲线得到最优平滑约束；（2）改变断层倾角，找到使得观测数据和正演计算拟合最好的断层倾角；（3）根据前面两步得到的最优平滑约束和断层倾角求得地震同震破裂分布。

In the paper only the range of normal value and the description of frequency distribution are discussed. In theory the widely-used percentile method to determine the range of normal value is imperfected. Curve fitting method show some advantage in determining the range of normal value, but is difficult to calculate.

从理论上说明了现在常用的确定正常值范围的方法存在一定的问题，尤其证明了大家使用得比较多的百分位数法存在的缺陷，说明了曲线拟合法的优点，而在频数分布拟合完成之后，就已经找到了频数分布资料的理论分布曲线，有了理论分布函数，我们利用分布函数计算正常值范围就比较容易，也比较准确。

Carrying out a fitting to curves between rising height of capillary water and time with various functions,it found that fitting effect was best with secondary polynome regression equations under the log coordinate.

对毛细水上升高度与时间关系试验曲线用各种函数进行了拟合，发现毛细水上升高度与时间过程在对数坐标下用二次多项式回归方程进行拟合效果最好。

Besides, the problem of a tabulated curve fitting is discussed and a method of improved B-spline multiple knot is presented.

另外，本文还对列表点曲线的拟合问题进行了讨论，提出了改进的重节点B样条拟合方法。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。