拖板

Table extension units and the pressure rail of bed, using V-quiet pressure rail movement smooth and good shock absorption.

工作台拖板与床身水平导轨，采用 V-平静压导轨运动平稳吸震性好。

The machine is a dedicated Milling Machine, Its bed and the overall structure of a lathe, Cutting function of the milling, Principle of its total whole installation box cutter and the drive shaft extension units of a large Worktable movement, Enter the hole, With Finger-shaped cutter Milling to Processing the hole keyway.

本机床是一台专用的车铣床，其床身和总体结构为一台车床，切削功能为铣削，其总原理为将整个铣头和传动轴通过大拖板的运动，伸入孔内，用指状铣刀来铣削加工内孔键槽。

The most common form of lathe is the turret lathe it consists of a horizontal bed supporting the headstock, the carriage and the turret.

最常见的车床形式是以图解方式显示的六角车床，它由一个支承床头箱、拖板和六角刀架的水平床身组成。

The spindle selects enclosed rolling bearing for supporting; vertical and horizontal drag board are adopted with enclosed rolling rod drive; body guide ways are casted with abrasion-resistance iron quenched with super frequency and milled precisely, and all these contribute to a long-term processing precision and a long lifespan; 5.5KW motor serves as the main motor contribute to a stronger turning capacity and larger rotary speed range; Workpiece clamping is are adopted withed with spring collet, it can also be equipped with hydraulic chuck, four-spindle oil cylinder, pneumatic, hydraulic tail stock.

CK6232数控车床是一款高刚性封密数控车床，特别适宜粗精加工，整机造型稳重大方，全封闭护罩防护，主轴采用精密刚性轴承支撑，纵横向拖板采用精密滚珠丝杆传动，床身导轨采用耐磨铸铁铸造，经超音频淬火及精密磨削，能长期稳定的保证加工精度和使用寿命；主电机选用5.5KW 的电机，使主轴有更强的切削能力和转速范围；工件装夹方式选用弹簧夹头，也可按用户要求配置手动卡盘、液压卡盘，气压、液压尾座。

This consists of a base, which is mounted on the cross slide so that it can be pivoted about a vertical axis, and an upper casting.

大多数车床的刀架安装在复式刀座上，刀座上有底座，底座安装在横拖板上，可绕垂直轴和上刀架转动。

To impart powered movement to the carriage and cross slide, a rotating feed rod is provided.

光杠通过摩擦离合器驱动拖板移动，离合器可能会产生打滑现象。

With a spring installed inside table, you can move it up and down, and it can adjust the pressure, swing it before and after by eccentric wheel and pulley. The swing margin is about 12 degrees. The platform was installed in the L-plate and can correct center to ensure die non-deformation and roundness in polishing process.

工作台里面安装弹簧一根，可以上下移动，并可任意调整压力，利用皮带轮和偏心轮带动，使前后摆动，摆动幅度约12度，而工作台被安装在 L 型拖板上可以任意地对中心，确保在抛光的过程中，使模具不变形及圆度。

Thus, through this gear train, leading from the spindle to the quick-change gear box, thence to the lead screw and feed rod, and then to the carriage, the cutting tooling tool can be made to move a specific distance, either longitudinally or transversely, for each revolution of the spindle.

主轴就是这样通过齿轮传动链来驱动变速齿轮箱，再带动丝杠和光杠，然后带动拖板，刀具就可以按主轴的转数纵向的或横向地精确移动。

Thus, through this gear train, leading from the spindle to the quick-change gear box, thence to the lead screw and feed rod, and then to the carriage, the cutting tool can be made to move a specific distance, either longitudinally or transversely, for each revolution of the spindle.

主轴就是这样通过齿轮传动链驱动变速齿轮箱，再带动丝杠和光杠，然后带动拖板，刀具就可以按主轴的转数纵向地或横向地精确移动。

These are the bed , headstock assembly, tailstock assembly, carriage assembly, quick-change gear box, and the leadscrew and feed rod.

车床的主要部件：床身、主轴箱组件、尾架组件、拖板组件、变速齿轮箱、丝杠和光杠。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。