拉杆

The Huangjie Bag Factory is specialized in design and production of various fashion bags, including studentsbag,travel bag,attache case,leisure bag,mommy bag,backpacking bag,pull bag and waist pack.

包袋厂主要设计，生产各种具有时尚风情的各式包袋。包袋。包括学生包，旅游包，公事包，休闲包，妈咪包，登山包，拉杆包，腰包，以及款式多样的女士等十多个系列，上千款式。

When cutting tool roaled of spindle's hole by manipulator or other ways,the pull nail behind of knife hilts is sent to ahead of tension bar of spindle. When receives the clamps signal, the pressure oil is passed over the oil cylinder left cavity of the spindle rear part, the piston to the right migration ,tension bar also to right migration by small dish shape spring function, the stell ball of ahead circumference of the tension bar shrink the distribution diameter by spindle's cone hole's force, holds on the knife hilts and pull nail colsely.

当刀具由机械手或用其他方法装到主轴孔后，其刀柄后部的拉钉便被送到主轴内拉杆的前端，当接到夹紧信号时，将压力油通入主轴尾部的油缸左腔，活塞向右移动，拉杆在碟形弹簧的作用下也向右移动，其前端圆周上的钢球在主轴锥孔的逼迫下收缩分布直径，将刀柄拉钉紧紧拉住。

"It consists of steering wheel, steering shaft, worm, gear sector, pitman arm drag link, steering knuckle arm, king pin, steering arms, tie rod, front axle and steering knuckle."

转向系统包括转向盘、转向轴、蜗杆、扇形齿轮、转向摇臂、直拉杆、转向节臂、主销、转向臂、转向直拉杆、前轴和转向节。到中国译典经典版本中查找关于pitman的最新解释和例句。。。。

Mainly thimble, reset rod, Secretary extinguishers (use of international standards such as the Japanese JIS, German DIN); SUJ2 derivative bearing steel columns, Introduction sets (using the Japanese "Fu Aventis" standard); jack mouth S45C high-quality steel products (use of international standards ), SKD11 Chong-pin, SKH51 straight needle, SUJ2 straight needle; there straight guide columns, occasional columns, sets of straight guide, care kits, gate kits rod guide column, bar ring, oblique derivative columns, quenching cylindrical, silver steel bars, flat die springs, black line round springs, high-speed steel Chong-pin, water Tsui, positioning ring, locking independent guide columns, sliding-oriented pieces, rolling-oriented pieces, heating tube , dual electric, high temperature wire, insulation casing, Nagarze wiring accessories such as mold.

主要有顶针、复位杆、司筒（采用国际标准如日本JIS、德国DIN）；SUJ2轴承钢导柱、导套（采用日本&富特巴&标准）；唧觜选用优质S45C钢材，SKD11冲针、SKH51直冲针、SUJ2直冲针；还有直导柱、托柱、直导套、托套、浇口套拉杆导柱、拉杆挡圈、斜导柱、淬火圆柱、银钢枝、模具扁弹簧、黑线圆弹簧、高速钢冲针、水咀、定位圈、锁扣独立导柱、滑动导向件、滚动导向件、加热管、电热偶、高温导线、绝缘套管、接线卡子等模具配件。

In view of the lack of effective methods for the measurement of internal force under the construction loads and the long-term monitoring in service of steel tie rods, a novel high-durable smart steel tie rod based on the fiber Bragg grating absolute measuring technology and packaged by glass fiber reinforced plastic was developed.

针对目前钢拉杆构件缺少施工荷载下的内力测试和服役期间的长期监测手段问题，采用玻璃钢封装技术研制开发出一种新型的基于光纤光栅绝对测量传感技术的高耐久性智能钢拉杆。

Main products of the Company are: auto seats for Minibus and minicar, interior plat, noise silencer assembly, steering assembly, horizontal and vertical pull rod assembly, stabling pulling rod assembly, bumper assembly, tank cover assembly, wiring assembly, heat insulation underlay, molding top and various pressings.

公司的主导产品为轻型车、微型车配套的全车座椅、内饰板、消声器总成、转向器总成、横、纵拉杆总成、稳定拉杆总成、保险杠总成、水箱面罩总成、线束总成、隔热垫、成型顶以及各种冲压件。

A space kinematics equation of the front wheel's steering rod mechanism was built through the steering rod mechanism of the rhombic vehicle that was symmetrical about front and rear.

根据菱形车转向系统转向拉杆机构前后对称的特点，为前轮转向拉杆机构建立了空间运动学方程。

A rod, called a tie rod, connects to each and of the rack.

拉杆，或称为转向拉杆，与摇臂的另一端连接。

This paper describs the requirements of testing members to be nominal, the precedure of exerting load upon the tension rod, specific cautions and the effect upon the construction, for the application of the shear type constant force tester to measure initial tensile force of the rod in the wharf construction for the Port of Tangshan .

阐述在唐山港码头施工中应用剪式恒力仪测定拉杆初拉力时对标定试件材料的要求、拉杆施力的过程和须注意的具体问题以及施工效果。

We can arch the black for the front and back, while the sides would be flushed and straight across with the arch.

黑色的拉杆放前后都可以，然后边上必须垂直并且穿过拉杆

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。