拉杆

According to actual requirements,some strengthening methods such as steel tie rod ,sticking steel,steel brace and steel bearing are chosen to reinforce the cantilevers.

根据实际需要，有针对性地选用多种加固方法(钢拉杆、粘钢、钢支撑和钢支座)来加固悬挑梁。

It is found that the stiffness of the beam is inadequate, which result in two gaps between the central beams of the moving beam; there are two weak strength sections where existing in the tie rod cylindrical hole and chamfering nearby the perforation cylinder.

通过分析发现横梁的刚度不足，致使中梁之间有两处开缝；强度较薄弱存在两处，分布在拉杆的圆柱孔边和穿孔缸附近的倒角处。

For corrosive environments, where dirt and abrasives may be ingested, and cause seals to wear faster than normally expected, the AFO offers the benefit of tie rod construction.

因为，腐蚀性环境中，灰尘和磨料可能摄入，并导致密封穿比通常预期的速度更快，踝足矫形器提供了拉杆工程受益。

Please note that these switches are compatible with all Numatics magnets with the exception of older style Hall effect magnets for tie rod cylinders （magnet code 3 option）.

请注意，这些开关是与年纪较大的风格馆拉杆气缸（磁代码3选择）起磁铁外，所有纽曼帝克磁铁兼容。

The tightening torques stated on table 1 are calculated for a tie rod stress equal to that allowable provided for such materials in ASME B31.3 and considers the leads provided on the flanges .

表1中所列的拧紧扭矩是按拉杆计算，且其应力取 ASME B31.3中该材料上的容许施加的应力，同时还考虑了法兰上的负荷。

This condition will be met if the inner steerable wheel turns through a larger angle than the outer one which is accomplished by the trapezoid-shaped steering linkage whose bases are the tie rod and the front axle, while the sides are the knuckle arms.

这种情况将会遇到的内在驱动轮转动角度通过一个大，比外trapezoid-shaped转向系统实现的基础是拉杆、前桥，而双方的指关节武器。

Forging, installation and monitoring technology of steel tension rod in beam string structure［J］.

张弦梁实心钢拉杆的锻造、安装和监测技术［J］。

By analyzing a monofilament cable, it is presented the conclusions that the influencing factors of the load-carrying properties of flexible supporting s stem include the initial prestress the diameter of tension rod or cable, the rise ratio and the height of the structure etc.

通过对单根拉索结构的力学分析，提出影响这种结构刚度和承载性能的因素主要包括：初始施加预应力的大小、拉杆的直径、结构的腹高比以及结构的高度等。

The writer set up an optimization-programming model to define preload and tension rod diameter by using constrained variable metric method.

文中采用约束变尺度法建立了确定预紧力和拉杆直径的优化计算模型，算例表明该方法可行。

Construction technique of high-strength steel tension rod for Shenzhen Convention and Exhibition Center［J］.

祁海王申。深圳会展中心高强度钢拉杆施工技术［J］。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。