拉孔

By the end of 2006 the Company conform to market demand and customer, using its own equipment, and use many years of experience and expertise (especially deep pull body and deep-hole plating technology), launched the "KETIAN" Branch Tin licensing hydraulic buffer hinge product line.

2006年底本公司顺应市场需求和客户推祟，利用自有的设备，及运用多年的经验和专业技术(特别是深拉身和深孔电镀技术)，推出了&KETIAN&科田牌液压缓冲铰链系列产品。

Hongye Machinery Factory production of machinery and equipment are widely used in metal processing production: Qi mouth edge, flat crimping, both inside and outside vertical crimping, pressure Blankholder bones, stretch forming, anti-side, crossed, metal ring inside the edge volume, Hemming, sand at the end, both inside and outside the sanding, the appearance of Belt Line, both inside and outside the skin polished, red-shaped punching, vol cylindrical, straight seam welding, weld line pressure, girth welding, pressure ring weld, sheet metal coated oil, pressure spiral teeth, cars spiral teeth.

鸿业机械厂生产的机械设备广泛用于五金制品加工生产：齐口切边、平面卷边、垂直内外卷边、压边压骨、拉形、反边、划线、金属圈卷内边、包边、砂底、内外砂光、外表砂带线、内外去皮抛光、冲形冲孔、卷圆筒、直缝焊、压直线焊缝、环缝焊、压环形焊缝、金属片涂油等、压螺旋牙、车螺旋牙。

Seeling, etc. explored at a two-way hollow mold hearth pore distribution, and Chen and Zhou indicate stress state on cavitation phenomena can be used bi-directional tensile test.

泽林等探讨了在双向炉缸模具中空孔分布，而陈和周表明应力状态对空穴现象的影响可利用双向拉伸实验。

The Hispaniola was rolling scuppers under in the ocean swell.

随着伊斯班袅拉号船身的摆动，排水孔几乎没到了水下。

If as a result of body shell keycap stuck with the key causes of the "key card" failure, may be key in the cap and put a gasket between the pads can be used稍硬some plastic (such as floppy disk jacket abandoned) made, its size is equal to or slightly larger than the key body size, and location by the rod through the ammonium can open a free passage under the square hole, in accordance with its set of poles, the plug cap; use this pad chip cap with the key body to prevent stuck, you can repair button; If as a result of spring fatigue, shrapnel resistance causes large card key failure, then the Special button to open the body, a little stretching to restore flexibility to reset the spring; Remove the key precursor to the resumption of shrapnel.

若是由于键帽与键体外壳卡住的原因造成&卡键&故障，则可在键帽与键体之间放一个垫片，该垫片可用稍硬一些的塑料做成，其大小等于或略大于键体尺寸，并且在按杆通过的位置开一个可使铵杆自由通过的方孔，将其套在按杆上后，插上键帽；用此垫片阻止键帽与键体卡住，即可修复故障按键；若是由于弹簧疲劳，弹片阻力变大的原因造成卡键故障，这时可特键体打开，稍微拉伸复位弹簧使其恢复弹性；取下弹片将键体恢复。

The loop flushing relief valve poppet includes an orifice which controls flushing flow under most conditions.

河套法拉盛包括减免可爱孔口控制阀冲在最流通的条件。

Initially it was the Oratorians at S Maria della Consolazione who supported the oratorio with works by Giovanni Legrenzi maestro di cappella at St Marks dominating the repertoire.

起初，它是在S玛利亚孔索拉齐奥（该法瓦的Oratorians）支持谁在圣商标与工程独霸演奏大师乔万尼莱格伦齐迪无伴奏合唱清唱剧。

Pull the switch out from the mounting hole in the door opening far enough to access the wire harness connector.

从车门洞里的固定孔中将开关拉出足够远，以便能处理线束接头。

CNC surrounding attachment: all kinds of holders, body, chuck, chuck handle, adjustable boring hole, and tapping devices, BT pull bolt head, Tool Cart, spindle cleaning rods, lock knife blocks, all kinds of Z-axis settings Miriam, 3D form, eccentric type, photoelectric devices, such as edge finding.

CNC周边附件：各式刀杆、本体、夹头、夹头柄、可调式搪孔器、攻牙器、BT螺栓拉头、刀具车、主轴清洁棒、锁刀座、各种Z轴设定仪、3D表、偏心式、光电式寻边器等。

Lift is not the answer. In my opinion the answer is in your wrist. The bowlers that rev the ball have a greater angle change in their wrist during the thumb exiting the ball.

提拉并不是解决之道，我觉得问题在於手腕的运用，高转速的球员在姆指脱离球孔以后，手腕会作出相当程度的角度变化。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。