抛物面的

Then the reflected shock wave produced by the parabolic reflector in resonator cavity frequently penetrated the flame, which led to continuous flame excitation.

共振腔抛物面的不同形状引起激波聚焦位置的变化，会影响激波和火焰的相互作用，使起爆提前或推迟，甚至不起爆。

The author not only presents pseudo sphere, ellipsoid ,conoid,uniported hyperboloid,elliptic biparted hyperboloid,paraboloid and hyperbolic paraboloid of the second elemental form,but also curve of the second elemental form.

不但给以了伪球面、椭圆面、劈锥曲面、单叶双曲面、双叶双曲面、椭圆抛物面及双曲抛物面的第二基本形式，而且给以了一般曲面的第二基本形式。

The high precision reflector panel is part of a paraboloid of revolution. Taking the forming technique of separated manufacture, the precision of the panel edge is important as it is a curve in space.

高精度反射器面板型面为旋转抛物面的一部分，采用分块成形拼接安装的方法制造，每块面板的边缘形状为空间曲线，对边缘精度要求很高。

F/D! When the plane that cuts the paraboloid is not perpendicular to the axis, elliptic segment of paraboloid is gained, whose focus is not in the geometric center of the parabolic surface, but is more or less shifted towards periphery, depending on the cut angle.

当抛物面切割面不垂直于轴线，就得到椭圆形的截面，它的焦点不在抛物面的几何中心，差不多移到边缘附近，随切割角度而定。

The feed radiation angle, both in horizontal and in vertical plane has to be the same, regardless the ellipticity of offset parabola.

馈源的方向角在水平和垂直都应当相同。而不管偏馈抛物面的椭圆率如何。

This can be a least-squares plane or a plane passing through the center of gravity of the corners and is parallel to the mid-rulings of the hyperbolic paraboloid determined by the corners.

这可以是一个最小平方平面或者是一个通过拐角的重心并且平行于由拐点决定的双曲线抛物面的半轴的平面。

That point must be placed in the focus of the parabola as precisely as possible!

这一点必须尽可能准确地放置在抛物面的焦点！

The convergence effect of reflected light was simulated in the paraboloid connected with small plane mirrors.

利用小平面镜逼近抛物面的方法研究车灯线光源的设计问题，通过在抛物面内内接小平面镜模拟抛物面反射光线的汇聚作用。

At last, the author presents the multi-coordinate NC machining methods of turbine wheel with non-developable ruled paraboloid.

从理论上深入分析了叶型为非可展直纹抛物面的叶轮的五坐标侧铣、四坐标侧铣和三坐标端铣数控加工计算方法。

Taking FANUC-0i NC System for example,this paper introduces the methods of machining paraboloid and some points for atte-ntion by using macroprogram .

以FANUC-0i数控系统为例，介绍在数控车床上用宏程序加工抛物面的方法以及一些注意事项，介绍用分支语句和重复语句编写加工抛物面的粗、精加工程序的技巧。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。