抛物线

In addition also using algebra interpolation leveling system error, including the linear interpolation, the parabola interpolation and the partition interpolation.

此外还利用代数插值法校正系统误差，其中包括线形插值法、抛物线插值法和分段插值法。

Function graphing and analyzing: 2D, 2.5D functiongraphs and animations, extrema, root, tangent, limit,derivative, integral, inverse; sequence of number: arithmetic progression, geometric progression; analytic geometry: vector, line, circle, ellipse,hyperbola and parabola; solid geometry: spatial line, prism, pyramid, cylinder, cone, dado and sphere; Ability to save graph as data file or bmp file; Ability to save animation as AVI file; Ability to move, zoom in, zoom out and rotate the scene.

函数图表和分析：2D， 2.5D 函数图表和动画，极值，根，正切，极限，导数；序列号：等差数列，等比级数；解析几何：向量，矢量，直线，圆，椭圆，双曲线和抛物线；立体几何：空间线，棱柱，三角锥，圆柱，圆锥体，梯形台和球体；保存图形为数据文件或者图像文件的功能；保存动画为 AVI 文件的功能；移动，缩小，放大和旋转场景的功能。

The results show that the oxide process follows parabolic kinetics at 600, 700, 800 ℃ for 180 min.

结果表明，分别在600、700、800 ℃氧化180 min的过程基本遵循抛物线规律。

The calculating formula of parabola and the length of ellipse arc can be found in the old handbook of mathematics, but it is inconvenient to be used in practice, especially, the accurate value is too difficult to get to.

关于抛物线和椭圆弧长的计算公式在数学手册和有关用表中早就可见。但实际上用起来很麻烦，其精确值也较难达到。

After the fatigue curve with 50% reliability and a few fatigue test results of a crane element have been known, the method, namely JFKC method, in this paper can be used to get the fatigue limiting stress distribution of this crane element quickly, based on the Miner Hypothesis and.

本文在已知某种起重机零件可靠度为50%的疲劳曲线并有了该种零件的少量试件的疫劳试验结果的条件下，以作者提出的修正的曼耐尔假设和抛物线假设为基础，提出了起重机零件疲劳极限应力分布的快速测定法——JFKC*法。

For the long period of oxidation, the Wagner's law for thick film oxidations was obeyed above 1000℃, that is the parabola relationship exists between the oxidation rate and the oxidation time, whereas there exists a linear dependence between them as the temperature is lower than 1000℃.

对于较长时间的氧化而言，CVDRe在1000℃以上的氧化遵循瓦格纳的厚膜氧化规律，即氧化速率遵从抛物线定律；而在较低的温度，CVDRe的氧化失重与时间呈直线关系。

Flow characteristics are linear, parabolic two.

流量特性有直线、抛物线两种。

Control valve flow characteristics are linear features, such as the percentage of properties and characteristics of three kinds of parabola.

调节阀的流量特性有线性特性，等百分比特性及抛物线特性三种。三种注量特性的意义如下

Control valve flow characteristics are linear features, such as the percentage Needle Valves of properties and characteristics of three kinds of parabola.

调节阀的流量特性有线性特性，等百分比特性及抛物线特性三种。

This paper analyze the stability of soil-nail wall with limit balanced analytical method, and assume the slip surface, destroy surface as dual fold line, circular arc line, parabolic curve or log spiral curve etc.

本文采用极限平衡分析方法对土钉墙内部稳定性进行了分析，滑动面、破坏面的形状假定为双折线、圆弧线、抛物线或对数螺旋曲线进行了描述。

By the time of its fall, most of the prisoners were writers who had written against the corruptions of the government.

到它被攻陷的时候，里面多数的犯人是写了反对政府贪污文章的作家。

The most obvious variation to ovum morphological character was that the color was changed from light green to sepiaceous in embryonic development, and all the ovums were almost hatched after 96h.

在胚胎发育过程中卵的形态特征最明显的变化是颜色从淡绿到深褐色，卵在发育96h后卵基本全部孵化。