投影线

The problem caused by internal off-line measuring, the lower product uniformity of the optical multifilament, is solved.

复丝基本参数在线检测仪采用了二维激光扫描技术，分别检测出两个垂直方向上投影的尺寸，通过理论计算得出六棱柱体的内切圆和外接圆直径，解决了目前国内复丝的离线检测所导致的复丝产品一致性差的问题。

The highest point, the nodus of the sundial, is 1025 cm from the ground.

其投影的地面铺有石块，并有十三条很好的二十四节气日期线。

The authors use the projection method to solve the segmenting problem of the characters in the case of character adhered or intersected with the lines, which made the recognition accuracy of the omnirange string increased.

运用波形投影方法解决了粘连字符及字线相交情况下的字间切割问题，使工程图多向字符识别精度显著提高，该算法对局部退化状态下的字符识别具有良好的抗干扰性。

Through studying the intersection of paraboloid of revolution and cylinder , the author concluded that the horizontal projection of the intersecting lines—, is the famous Four-order algebra curve-Perseus curve.

通过对回转抛物面与圆柱面相交的研究，得出交线的水平投影曲线——为四次代数曲线——Perseus座曲线的结论。

With high precision linear CCD as measuring sensor and combining with a mechanical scanning method,a quick measurement for the aperture of wire drawing die is carried out by the parallel light projection method.

采用平行光投影法，以高精度线阵 CCD为测量传感器，结合机械扫描方法，完成对拉丝模孔径的快速检测。

To achieve better than first-order accuracy in Godunov method, a piecewise linear function instead of a piecewise constant function is used along the line between the centroids of two neighbored cells.

为了提高Godunov算法的求解精度，本文将相邻两个三角形单元重心连线上的参数分布看作是分段线性函数，线性函数的坡度取决于网格单元内参数分布的梯度在插值方向的投影。

As the projector can conceptually be regarded as camera acting in reverse, the relation between projection plane of the projector and imaging plane of the camera is fixed.

进而， 利用投影仪的投射过程是摄像机成像过程的逆过程，建立投影仪的投射平面和摄像机的成像平面的对应关系，将"极线几何约束"应用到基于条纹投影的主动三维视觉的姿态估计问题，并在考虑测量数据受噪声影响的条件下，建立了求解视点姿态参量的数学模型。

Using guyed tower middle line insulator string as an object, through analyzing of distance between cross arm and boom guy plumb plane, and projecting insulator string length, angle, conductor wind inclined angle, and sag to boom guy plumb plane, middle line insulator string tracking equations can be established.

以拉线塔中线绝缘子串为分析对象，通过对横担、拉线铅锤面间的距离分析，再将绝缘子的串长、角度，导线风偏角、弧垂投影至拉线铅锤面，在拉线铅锤面建立中线绝缘子串的轨迹方程，以带电体与拉线间的距离为限制条件，从不同角度计算出第1、2、3极限风偏角，取其中的最小值为极限风偏角。

The system utilized four laser scanners along lengthwise direction of the log. Data are obtained in every ten degrees when log is turning, in each cross section, 36 data are obtained. Then the data obtained were processed and an outline of the cross section of the log was developed on computer screen. Afterwards, the largest inscribed circles for log cross sections were determined according to the principle that three points can determine a circle. Secondly, the points located on the cross sections were linked up along some log generative in order to simulate the three-dimension log outline. At last the largest right circular cylinder were optimized and the optimum turning center was determined by means of projective theory.

具体作法是：在木段长度方向均匀设置四个激光传感器，当木段旋转时，起动激光传感器，进行数据采集，每隔10~0扫描一个点，在各横断面圆周上共采集36个点的数据，由计算机处理采集的数据，并绘制出原木横断面的几何图形，再根据三点定圆的原理，确定出最大内接圆；其次，模拟原木三维廓形，即将原木相邻横断面上离散点沿着母线方向连线，由计算机分析处理，绘制原木三维廓形；最后，采用投影法，优化出原木最大内接圆柱体，并确定原木回转中心线。

In this paper,three problems are researched.First,a method for recognizing triangle and quadrangle is introduced based on geometry and angle constraint.Then Attribute Relation Graph is employed to describe simple polyhedron and line drawing.

依据投影几何中的距离约束和角度约束，给出了三边形和平行四边形的识别方法；提出用属性关系图表示平面立体和线图，该描述方法是一种结合表面特征和几何特征的方法。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。