扭转

Methods 40 healthy adult Wistar rats were divided randomly into four groups, sham operation group (group A, n=10), torsion/detorsion group (group B, n=10), single astragalus plus detorsion group (group C, n=10), successive astragalus plus detorsion group (group D, n=10). Testicular torsion/detorsion model was established in terms of turner methods.

将40只健康雄性Wistar大鼠分为4组，分别为假手术对照组，睾丸扭转／复位组，睾丸扭转／复位＋单次腹腔内注射黄芪注射液组及扭转／复位＋连续腹腔内注射黄芪注射液组，每组10只。

New boundary integral equations for the torsion problem of an isotropic bar with curvilinear cracks are derived by using integration by parts and other techniques to the traditional boundary integral formulations. And the boundary integral equations for the torsion problem of an anisotropic bar with curvilinear cracks are also derived by using the isotropicalized boundary element method. Then the anisotropic problem can be solved on the base of the boundary element method of isotropic problem.

然后用各向同性化方法，将各向异性材料裂纹柱体的扭转问题转化为各向同性材料的问题，在各向同性材料裂纹柱体扭转问题的新的边界积分方程的基础上，推导出了适用于各向异性材料裂纹柱体扭转问题的边界积分方程，然后按已推导出的各向同性问题的边界元法求解。

The natural twist vibration equation is set up by making use of the constitutive relation of nonlinear material.

利用非线性材料的本构关系，建立了非线性材料圆杆的扭转固有振动方程，然后采用傅立叶级数法求得了圆杆扭转固有振动的所似解，通过实例计算讨论分析了非线性材料圆杆的扭转固有振动特性。

The pressure fluctuations were measured at different positions along the axial direction on the tonge. The coherence analysis was utilized for illustrating the blade passing frequency cancellation mechanism. A 3-D flow visualization method, which overcame the blind slight from LDV and PTV, was used to present the differences of internal flow patterns.

实验中分别进行0度、5度与10度三种叶轮扭转角之设计，在横流扇出风口以声学人偶进行噪音量测，评估不同叶轮扭转角在操作转速下之风扇噪音、并分析其声音品质；另外在舌端上不同的轴向位置撷取其压力扰动频谱进行相干性分析，探讨舌端上因不同叶轮扭转角对周期性压力扰动之破坏之探讨。

By applying one couple of unit force on two suspension centers based on 3D FEM to calculate their relative displacement, coefficient of torsion displacement, the radial gate s torsional rigidity coefficient is derived; and its stress distribution is analyzed to solve radial gate s torsion problem.

基于空间有限单元法，对闸门吊点施加1对单位力计算出2个吊点的相对位移———闸门扭转挠度系数，进而推算出闸门抗扭刚度系数和单位位移下的应力状态，据此最终解决弧门的扭转问题。并通过某一工程实例的分析计算，表明该方法在生产设计中具有较好的实用性，可以有效地解决弧形闸门的扭转计算问题

If it does twist, but the twist is less than 180 degrees, it is called a torsion.

如果不扭转，但扭转小于180度，它被称为扭转。

Limit,torsion modulus of elasticity, modulus of rupture in torsion, and Torsional Strength.

应力-应变图，以测定扭转弹性极限、弹性模量，扭转中的断裂模量和扭转强度。

Through the analysis of the torsional stress produced in the open sections vehicle frame s under typical operation conditions the calculating formula is achieveal,which leads to the stress distribution of the open section frame and the ideas of improving the distribution of the torsional stress are discussed.

通过对常见开口截面车架在典型工况时扭转应力的分析，推导出扭转应力计算公式，从而得出了开口截面车架的一些应力分布规律，提出了改善车架扭转应力分布的具体措施。对汽车车架设计方案的拟定和车架应力分析具有指导作用

The determination of AHT value mathematical formula is one of the mo-st important problems during the design of three dimensional software packagfor directionally drilled well.

在研究定向井三维设计软件包时，软件设计程序要满足全方位的扭转中的一个重要问题就是如何确定最终方位角AHT值数学表达式；本文针对定向井在全方位扭转条件下扭转后最终方位角的变化规律进行深入研究。

objective:to improve the diagnosis and treatment of testicular torsion.methods:the date of 13 cases of testieular torsion 2003.8～2008.5 in our hospital were retrospectively analyzed.results:all of the 13 cases were assessed correctly by cdfi,among them,excision 6,1 undescended testis,under-took orehiopexy.

目的：提高睾丸扭转的诊治水平。方法：对我院2003年8月～2008年5月收治的13例睾丸扭转的诊断及治疗作回顾性分析。结果：13例均行cdfi确诊，其中手术切除9例，3例为隐睾扭转，因睾丸生机恢复而行睾丸固定术。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。