扭矩

That's over a ton, and seems very heavy for a 40 HP engine In the compound design, the two rotor assemblies were staggered in angular alignment to smooth out the torque delivery.

也就是超过1吨，和似乎非常繁忙，为一个40马力发动机）在该化合物的设计，两个转子集会错开，角对齐，以理顺扭矩交付。

An inside conical surface at the lower end of the joint is designed to ensure the shaft swing freely within an angle range of 10°, thereby the axial bending stress caused by the deflection of the borehole can be eliminated effectively.

这种装置采用类似球形关节的旋转机构，消除了抽油杆柱上下往复运动产生的倒扣扭矩；在短节下端设计有10°的内圆锥表面，使转轴能够在10°范围内自由转动，从而有效地消除了由于井身弯曲而产生的轴向弯曲应力。

A connected set of rotating gears by which force is transmitted or motion or torque is changed.

能量被传送或运动或扭矩被改变的相互连接的一系列齿轮。

The counterbore at the crankcase joint line is to ensure that the stresses are distributed over a larger area in order to even out the clamping loads on the joint faces(line of max stress is at 45 degrees) this means that the clamping loads loads can ideally overlap at the joint face it also has the bonus of giving a longer bolt length which means less stress on the bolt for the same tightening torque.

该counterbore在曲轴箱的联合路线，是要确保该讲是分布面积较大，在以，甚至出夹紧载荷对联合所面临的（线的最高强调的是，在45度），这意味着，夹紧载荷载荷可以理想重叠在联合面对它也有奖金给予较长的螺栓的长度即减少应力对螺栓同时收紧扭矩。

For torque wrench with drive coupler 9 × 12 mm or 14 × 18 mm.

为扭力／扭矩扳手与推进耦合装置 9 × 12 毫米或 14 × 18 毫米。

It belongs the kind of complex bridges because its liner changes usually and the weight condition is also complex, except bear moment and shearing force, there are larger torsion and doubled moment, as a result, crankle、warping and aberration would happen.

这种异形桥梁结构是受力很复杂的一种桥型，其线性变化多端，结构受力复杂，除承受弯距、剪力外，还有较大扭矩和翘曲双力矩的作用，即使外荷载的作用通过梁的剪切中心，也将发生弯扭组合变形，同时伴随有截面的翘曲和畸变。

As tunneling and cutting equipment of a shield machine ,the cutterhead can excavate stratum,stabilize excavation face,mix soil slag, etc.

刀盘是机械化盾构机的掘削机构，具有开挖地层、稳定开挖面、搅拌渣土等功能，并承受大扭矩、大推力和冲击载荷的作用，其工作状况非常恶劣。

It is shown that the friction force and bulkhead thrust are the main factors of shield thrust setting, while the friction between the cutterhead and soil is the main factors of cutterhead torque setting. Friction force between shield and soil would make front soil of shield upheave, and subsidence of surface soil is induced by ground loss when the friction force between the cutterhead and soil results in the surface settlement asymmetrical distribution.

通过计算发现，盾构施工中盾壳摩擦和正面推力是盾构推力设置的主要因素，而刀盘与土体摩擦是刀盘扭矩设置的主要因素，盾构前方土体隆起主要由盾壳摩擦引起，刀盘摩擦作用主要引起地表沉降的非对称分布，地表沉降主要由盾尾空隙产生。

By considering torque characteristics of variable-frequency motors and mesh stiffness as well as backlash nonlinearity in gear transmission,a dynamics model for the cutting system of shield tunneling machine with redundant drives was established. The fluctuation characteristics of torque loads and dynamic cutterhead driving torque in composite strata were analyzed.

复合地层掘进扭矩载荷突变是造成盾构机掘进过程中堵转停机的直接原因，考虑盾构机刀盘驱动变频调速电机特性、转矩传递过程中齿轮啮合刚度及齿侧间隙等非线性因素，建立冗余驱动的盾构机刀盘切削系统机电耦合动力学模型；针对典型复合地层地质条件，对盾构机在上软下硬地层掘进过程中刀盘驱动转矩动态特性进行仿真分析。

Also, the drive is able to transfer larger torque and power than the existing planetary cycloid drive.

其具有体积小、重量轻、传动比范围大、传动效率高、传动平稳、结构简单、传递的扭矩和功率较传统摆线针轮行星传动成倍增大等一系列优点。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。