手动

You should also have kitchen accessories and cooking utensils, especially a manual can opener.

你还应该准备一些厨房用具和炊具，尤其是手动开罐器。

This design is to dials forks the components the processing craft and the jig design, its components are the forging, has the volume to be small, components complex characteristic,Because the surface is easier than the hole to process, when formulation technological process, first the machined surface, then processes other take the surface as the datum,In which various working procedures jig all uses the unit clamp, special regarding processes the big end of hole, the trough and drills the capitellum hole incline eyelet in the working procedure, Chooses locate mode which two sells at the same time, and operates the simple manual clamp way clamp, its organization design is simple, the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计，其零件为锻件，具有体积小，零件复杂的特点，由于面比孔易加工，在制定工艺规程时，就先加工面，再以面为基准来加工其它，其中各工序夹具都采用专用夹具，特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中，选一面两销的定位方式，并以操作简单的手动夹紧方式夹紧，其机构设计简单，方便且能满足要求。

This design is to dials forks the components the processing craft and the jig design its components are the forging has the volume to be small components complex characteristicBecause the surface is easier than the hole to process when formulation technological process first the machined surface then processes other take the surface as the datumIn which various working procedures jig all uses the unit clamp special regarding processes the big end of hole the trough and drills the capitellum hole incline eyelet in the working procedure Chooses locate mode which two sells at the same time and operates the simple manual clamp way clamp its organization design is simple the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计，其零件为锻件，具有体积小，零件复杂的特点，由于面比孔易加工，在制定工艺规程时，就先加工面，再以面为基准来加工其它，其中各工序夹具都采用专用夹具，特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中，选一面两销的定位方式，并以操作简单的手动夹紧方式夹紧，其机构设计简单，方便且能满足要求。关键词拨叉，加工工艺，专用夹具，设计

In this thesis, we use "Two-Step CVD Technique " to solve this problem, that is to carbonize Si substrate in carbide gas atmosphere first in order to form a Sio-rtd 0

将原先的热丝CVD法加热改为独创的石墨-碘钨灯加热，把衬底温度从900℃提高到1200℃；将手动控温改为PID自动控稳，大大提高了控制精度，实验中温度偏差小于1℃(衬底温度1200℃时)。

Our global customers to provide manual carpet sweeper .

我们向全球客户提供手动地毯清扫器。

Manual carpet sweeper - Price | Parameters | Specifications | Information - carpet cleaning | carpet pumping cleaning | carpet cleaning | carpet ...

手动地毯清扫器-价格|参数|规格|资料-地毯清洗|地毯抽洗|地毯清洁|地毯。。。

In particular, the Group still provide free manual carpet sweeper brush, clean, cleaning equipment, safety mats, carpet cleaning machines, small area of carpet cleaning machines.

尚尤集团提供免刷式手动地毯清扫器，环境清洁，清洁设备，安全地垫，地毯清洗机，中小面积地毯清洗机等。

In particular, the Group still provide free manual carpet sweeper brush, clean, clean equipment, safety mats, carpet cleaning machines, small area of carpet cleaning machines.

尚尤集团提供免刷式手动地毯清扫器，环境清洁，清洁设备，安全地垫，地毯清洗机，中小面积地毯清洗机等。

The drive transfer component can be operated manually in the carriage and drive output gears in the actuator.

驱动力传递构件，可从车厢内侧手动进行操作并且可以驱动促动器内的输出齿轮。

For long time, my factory prints a version to electroplate a group in addition to import of the nickel urn is full-automatic, other of five electroplates slot almost is depend on moving an operation to control to electroplate of temperature, electric current and time of, print a version to plate chrome especially, with its special operation craft and the high causticity, the long-term existence product quality unsteady problem, can not keep up with the request that assurance product quality unifier.

长久以来，上海印钞厂印版电镀小组除了进口的镍缸是全自动的，其它的五个电镀槽几乎都是依靠手动操作来控制电镀时的温度、电流和时间的，特别是印版镀铬，以其特殊的操作工艺和高度腐蚀性，长期存在产品质量不稳定的问题，跟不上保证产品质量的统一性的要求。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。