成形模具

Analyzing and simulating of the deformation law of the ceramic downspout product after overcoming the shortage of powder material models in the software of MSC. MARC. It shows out the important effects of various factors and the shape of mandril during the process. And it is obvious that the shape of the top mandril has more effects on the process than the bottom.(3) Showing out the important effects of model figure on the flowing of powder and the forming of low-density fields from the analysis. After changing the top of the mandril into spherical shape, an improving model is putting out so that the distribution of stress and strain turns to be even and proper and that the flow rule of powder grains is better.(4) Calculating of the dimensional precision and the cutting ratio of the product and analyzing of the effects of such factors as rubber aging, loading process, mandril, friction etc. on the cutting ratio.

MARC存在的粉末材料模型方面的设计缺陷后，对连铸水口粉末成形件的变形规律及影响因素作用进行了模拟分析，指出芯棒形状对成形件的变形有较大影响，并且芯棒顶部形状与芯棒底部形状相比，对粉末变形有更大影响；(3)分析了成形件出现低密度区域的原因，指出模具形状对粉末流动以及粉末成形件低密度区域的形成有重要作用，提出了密度分布优化改进模型：改进模具顶部形状，并将芯棒顶部设计成球面后，粉末成形件顶部区域的应力、应变分布更加均匀、合理，粉体颗粒流动情况明显改善，低密度区域明显缩小；(4)计算了成形件的尺寸精度及切削率，并指出除模具形状的影响外，充填密度、橡胶模具老化、加载工艺等其他因素对总体切削率也有相当的影响。

The micro mold after forming of electroform needs the increasing thickness process which inset in the block and supports the micro mold during the injection modeling. Otherwise, the buffer layers could prevent the problems of stresss and surface deterioration.

然而微模具在电铸成形后需经增厚处理，因为增厚处理使非常薄的微模具与模具基座较易配合，也将提供微模具於射出成形过程中之支撑，一般增厚制程会在微模具与增厚层间加入一缓冲层避免应力与表层变质造成之问题。

Considering the problems of spurgear precise plastic forming, such as high deformation resistance, poor flowability and especial hardness to fill cant of gear, technological plan was developed based on precise plastic forming technique, successive control principle and consecutive local deformation theory. Moreover, structures of the rolling preform die and the die with up and down wellrounded forcer for stamping-extrusion and bulge-extrusion combining forming were designed too.

因此本文的主要研究内容和结果如下：本文以某种直齿轮：模数m＝2，齿数z＝20，压力角α＝200，变位系数x＝0为对象，针对直齿轮精密塑性成形变形抗力大，流动性差，特别是成形中齿轮角隅部分更加难以充满问题，基于精密塑性成形技术、逐次控制原理以及连续局部变形原理提出了"直齿轮滚轧制坯－镦挤、胀挤复合精成形"的工艺方案，设计了滚轧制坯的模具结构和上下冲头带圆角的镦挤、胀挤复合精成形的模具结构。

Secondly, by the numerical simulation "experiments" and mechanics analyses, the effects of temperatures, forming velocities and the entering angles of mould on the products were studied. The main invaliding forms both of crinkling and crazing were simulated and analyzed, so that the technical parameters of forming, geometrical parameters of moulds were optimized.

其次，通过对TC1钛合金薄板整流内罩的深拉热成形的数值模拟&实验&和力学分析，探讨温度、成形速度和模具压边力等对成形产品的影响，模拟分析了&起皱&和&拉裂&等主要失效形式，对成形工艺参数、模具几何参数等进行了优化。

illustrates the forming die and a substrate sheet, which are subjected to a pressing process and FIG.

7条说明了成形模具和衬底资产负债表，这是受到一项紧迫的进程和图。

The technical process has been introduced. By analyzing the changes of pressure under different temperature, the forming die has been designed.

介绍了加工工艺流程，分析了不同温度时压力变化的情况，并据此设计出了成形模具。

illustrates a forming die on which ultraviolet ray curing type resin is applied, FIG.

条说明了成形模具上，紫外线固化型树脂的应用，图。

A metal mold for tire formation that realizes not only enhancing of evacuation efficiency at the time of tire vulcanization molding but also enhancing of the durability thereof; a plug for use in vent hole of such a metal mold for tire formation; and a tire manufactured with the use of the metal mold for tire formation.

本发明提供能够提高轮胎硫化成形时的排气效率、并且能够提高耐久性的轮胎成形用模具、轮胎成形用模具的通气孔所使用的塞子以及使用该轮胎成形用模具制造的轮胎。

Through the technical analysis of steel drawer panel,the technical solution is changed.

通过对钢质抽屉面的工艺分析，改变了工艺方案，充分利用设备特点，设计出一套应用于普通压力机上的多工位弯曲成形模具。

Considering the problems of spurgear precise plastic forming, such as high deformation resistance, poor flowability and especial hardness to fill cant of gear, technological plan was developed based on precise plastic forming technique, successive control principle and consecutive local deformation theory. Moreover, structures of the rolling preform die and the die with up and down wellrounded forcer for stamping-extrusion and bulge-extrusion combining forming were designed too.

因此本文的主要研究内容和结果如下：本文以某种直齿轮：模数m＝2，齿数z＝20，压力角α＝200，变位系数x＝0为对象，针对直齿轮精密塑性成形变形抗力大，流动性差，特别是成形中齿轮角隅部分更加难以充满问题，基于精密塑性成形技术、逐次控制原理以及连续局部变形原理提出了&直齿轮滚轧制坯－镦挤、胀挤复合精成形&的工艺方案，设计了滚轧制坯的模具结构和上下冲头带圆角的镦挤、胀挤复合精成形的模具结构。

Singer Leona Lewis and former Led Zeppelin guitarist Jimmy Page emerged as the bus transformed into a grass-covered carnival float, and the pair combined for a rendition of "Whole Lotta Love".

歌手leona刘易斯和前率领的飞艇的吉他手吉米页出现巴士转化为基层所涵盖的嘉年华花车，和一双合并为一移交&整个lotta爱&。

This is Kate, and that's Erin.

这是凯特，那个是爱朗。